Introduction

Remove the lower case to access the internal components of your MacBook Pro.

Image 1/1: Three 14.4 mm Phillips #00 screws
  • Remove the following ten screws:

    • Three 14.4 mm Phillips #00 screws

    • Three 3.5 mm Phillips #00 screws

    • Four 3.5 mm shouldered Phillips #00 screws

Does void the warranty?

jfondeur - Reply

No, it does not void the warranty. More specifically: http://eshop.macsales.com/Search/display...

oakdragon12 - Reply

How much weight can I save by removing the optical drive?

gunes314 - Reply

You can save a lot of weight if lets say your installing a solid state drive or putting in a second hard drive but if you know that you use the CD/DVD disc drive a lot then you might just want to leave the drive alone.

Marshall WahlstromHelgren -

Also wondering how much weight I'd save by just removing. My drive is broken for ages, but I have not needed it in ages. The HD was already replaced by a cheap SSD (second best thing after upgrading to 8GB), so I'd appreciate losing some weight. I mean, the computer. Although I could lose some too... erm... well, anyway, I guess the lack of the DVD would not interfere with anything, right? Opinions?

Carlos Duarte do Nascimento - Reply

Apple has meticulously balanced the MacBook's weight from left to right, and removing the optical drive may off-balance the Mac.

Seji the veggie -

What so you think that a removing the optical drive which weighs less than a AA battery will unbalance a MBP making it unusable? LOL!

Unless you use the MBP on a high wire (an even then I have my doubts) you'd never notice the weight difference.

pmhparis -

I'm thinking you'd probably be OK losing the DVD drive without a problem. Just make sure the optical drive cable is secured or you might hear it rattling in there from time-to-time.

John Adam Wickliffe - Reply

Hey guys,

this website is amazing. I read it to guide me on fixing my mac book pro, but on the video, the girl gives a wrong information.. She says that is not possible replace just the keyboard... But I managed to replace only my keyboard. It is boring because I have to remove approximately 70 screws but it is possible. Thanks a lot! You guys helped me save about US$300 thats because in Brazil some technicians would charge me with that amount!

I posted some pictures on your facebook page..

renatumb - Reply

Tip: Use one of those weekday pill holders to have a cheep way to store screws you remove and each day of the week can be for different sizes or parts. It has been handy to have (much less expensive than the magnetic mat.

Robert Wacker - Reply

Great tutorial. I found that using a Phillips #0 in lieu of the #00 worked much better.

kschmesk - Reply

I tried the PH #00 for the 10 screws that hold the bottom case and it's too big, instead PH #000 works perfectly. Are you sure this screws are #00?

Alex - Reply

The likely problem with your wifi is not the card but the antenna leads that go into the plastic clutch

. Ifixit don't have a guide to change this as it it includes the isight camera so the screen has to be disassembled which is fairly hard

I got round it by using the camera cable from the old set and cutting off the new one

brian whittle - Reply

Hello MacWorld,

Just want to say that this site is a great resource for repairing or upgrading your Mac. I had a bad SATA cable in my MacBook Pro and after ordering a new one from the "IFIXIT" site I received the cable within two days, replaced it and was up and running again in no time. Thanks IFIXIT for you help!

wer 10/5/15

tayseer999 - Reply

I have found that my MacBook Pro 13 Late 2011 has five shouldered screws and not four. I am not sure exactly where it goes but I have put it in the top left corner of the picture as it is the odd one out.

GotMac - Reply

Hello, where can I buy the screws I need in case I lose one of them?

taylornya - Reply

on my device the #00 screwdriver was a bit too small. a #0 was the perfect one

Maximilian Klotz - Reply

I found with mine that the shouldered and un-shouldered screws were reversed (the three un-shouldered screws going where the orange colour indicates). Also, I found that the front four screws went in at an angle.

gilded yak - Reply

I need to know why my party can't hear. Me on my android phone

Tina Porter - Reply

Because that party is inside your head Tino. Just close your eyes and enjoy the tunes

Snuf Box -

Are you sure the short screws are different? The set sold here just says “Seven 3 mm Phillips #00 screws.”

Jack - Reply

I have one stripped screw... How opening without drill it?! Any suggestions please?

rodrigosady - Reply

I used 3 eggcups to hold the screws ;>) They are very fiddly and easy to drop on floor so keep the MacBook away from the edge of the surface you are using to avoid accidentally dropping a screw off the edge of a table, etc.

Stephen Smith - Reply

A screw does not come out, how can I get it out? Many thanks in advance for your help

Wilder Torres - Reply

Image 1/2: Remove the lower case. Image 2/2: Remove the lower case.
  • Use your fingers to pry the lower case away from the body of the MacBook near the vent.

  • Remove the lower case.

If the black vent window that is attached to the back cover becomes loose what kind of glue should be used to attach it again, thermal paste or super glue?

Thanks for your help.

Mikell - Reply

Conclusion

To reassemble your device, follow these instructions in reverse order.

45 other people completed this guide.

One Comment

Has anyone had problems with the screen flickering after assembling the computer again? How can I solve this problem?

Laura Christiansen - Reply

Add Comment

View Statistics:

Past 24 Hours: 8

Past 7 Days: 81

Past 30 Days: 291

All Time: 24,926