Introduction

This is a replacement guide for the Logitech Harmony Smart Keyboard's key printed circuit board.

The keyboard printed circuit board (PCB) sends messages to the wifi and transmits key data to the server.

Turn keyboard over to the  backside. Turn keyboard over to the  backside.
  • Turn keyboard over to the backside.

Add Comment

Press and slide up on the upper battery latch, using both thumbs. Press and slide up on the upper battery latch, using both thumbs. Press and slide up on the upper battery latch, using both thumbs.
  • Press and slide up on the upper battery latch, using both thumbs.

Add Comment

Remove the two AA batteries and set them aside.
  • Remove the two AA batteries and set them aside.

Add Comment

Unscrew all five 4.0 mm screws, using Phillips #1 screwdriver. Unscrew all five 4.0 mm screws, using Phillips #1 screwdriver.
  • Unscrew all five 4.0 mm screws, using Phillips #1 screwdriver.

Add Comment

Peel off the center sticker to reveal two hidden 4.0 mm screws. Unscrew these two screws with a Phillips #1 screwdriver.
  • Peel off the center sticker to reveal two hidden 4.0 mm screws.

  • Unscrew these two screws with a Phillips #1 screwdriver.

Add Comment

Lift both top left and top right rubber stickers halfway, using the sharp end of the plastic spudger. Unscrew a total of two 4.0 mm screws, under the rubber stickers,  using a Phillips #1 screwdriver. Unscrew a total of two 4.0 mm screws, under the rubber stickers,  using a Phillips #1 screwdriver.
  • Lift both top left and top right rubber stickers halfway, using the sharp end of the plastic spudger.

  • Unscrew a total of two 4.0 mm screws, under the rubber stickers, using a Phillips #1 screwdriver.

Add Comment

Unscrew the top center 4.0 mm screw, in the battery compartment, using the Phillips  #1 screwdriver. Now, you should have a total of ten 4.0 mm screws set aside.
  • Unscrew the top center 4.0 mm screw, in the battery compartment, using the Phillips #1 screwdriver.

  • Now, you should have a total of ten 4.0 mm screws set aside.

Add Comment

Wedge the flat end of the spudger between the back panel and front panel. Slide the flat end of the spudger from right to left to pry the two panels apart. Slide the flat end of the spudger from right to left to pry the two panels apart.
  • Wedge the flat end of the spudger between the back panel and front panel.

  • Slide the flat end of the spudger from right to left to pry the two panels apart.

Add Comment

Separate the back panel from the front panel completely, using both hands. A white ribbon flex cable will remain connected to both panels. Pull the panels apart slowly and gently, or the white ribbon flex cable may be unsafely removed.
  • Separate the back panel from the front panel completely, using both hands.

  • A white ribbon flex cable will remain connected to both panels.

  • Pull the panels apart slowly and gently, or the white ribbon flex cable may be unsafely removed.

Add Comment

Grip the lower end of the ribbon flex cable (white band) using your thumb and index finger. Then slide the strip out toward yourself in a scooping motion. Now, you should  have two completely separated panel pieces.
  • Grip the lower end of the ribbon flex cable (white band) using your thumb and index finger.

  • Then slide the strip out toward yourself in a scooping motion.

  • Now, you should have two completely separated panel pieces.

Add Comment

Lift and remove the white rubber sheet that lays over the keyboard pet flexible PCB. Lift and remove the white rubber sheet that lays over the keyboard pet flexible PCB. Lift and remove the white rubber sheet that lays over the keyboard pet flexible PCB.
  • Lift and remove the white rubber sheet that lays over the keyboard pet flexible PCB.

Add Comment

Unscrew the two  4.0 mm screws on either side of the green card using a Phillips #1 screwdriver. Unscrew the two  4.0 mm screws on either side of the green card using a Phillips #1 screwdriver. Unscrew the two  4.0 mm screws on either side of the green card using a Phillips #1 screwdriver.
  • Unscrew the two 4.0 mm screws on either side of the green card using a Phillips #1 screwdriver.

Add Comment

Lift the green card up using the flat end of the plastic spudger.
  • Lift the green card up using the flat end of the plastic spudger.

Add Comment

Grip and lift the keyboard PCB up and out.
  • Grip and lift the keyboard PCB up and out.

  • The battery wires will remain connected.

Add Comment

Grip and lift the battery wire bar out of the battery compartment, using your thumb and index finger.
  • Grip and lift the battery wire bar out of the battery compartment, using your thumb and index finger.

Add Comment

Pinch your precision tweezers and wedge the battery clamp up. Lift the entire keyboard PCB out of the panel.
  • Pinch your precision tweezers and wedge the battery clamp up.

  • Lift the entire keyboard PCB out of the panel.

  • The keyboard PCB will remain connected to the green card.

Add Comment

Slide your index finger into the slot under the right blue tab. Pinch and pull the right blue tab away from the green card. Pinch and pull the right blue tab away from the green card.
  • Slide your index finger into the slot under the right blue tab.

  • Pinch and pull the right blue tab away from the green card.

Add Comment

Pinch and pull the left blue tab away from the green card. Pinch and pull the left blue tab away from the green card. Pinch and pull the left blue tab away from the green card.
  • Pinch and pull the left blue tab away from the green card.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Hayley Nichols

Member since: 09/05/2017

435 Reputation

4 Guides authored

Team

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 19

All Time: 209