Introduction

This guide explains how to remove the rear facing camera from the Miix 2 for an easy replacement.

Remove the back cover of the tablet by inserting nylon or metal spudger in the small hole between the screen and rear cover near the volume button. slide along the edge of the tablet to release the internal clasps. You should have to apply a good amount of force, but pry carefully in order to avoid damaging the clasps or the internals.
  • Remove the back cover of the tablet by inserting nylon or metal spudger in the small hole between the screen and rear cover near the volume button. slide along the edge of the tablet to release the internal clasps.

  • You should have to apply a good amount of force, but pry carefully in order to avoid damaging the clasps or the internals.

Add Comment

Unscrew the six 3mm J0 screws surrounding the battery dock. Unscrew the six 3mm J0 screws surrounding the battery dock.
  • Unscrew the six 3mm J0 screws surrounding the battery dock.

Add Comment

Using a plastic spudger, slowly push each side of the battery connector (back and forward a couple of times) out of its socket on the motherboard. Using a plastic spudger, slowly push each side of the battery connector (back and forward a couple of times) out of its socket on the motherboard.
  • Using a plastic spudger, slowly push each side of the battery connector (back and forward a couple of times) out of its socket on the motherboard.

Add Comment

Remove the battery by prying up with your fingers or a plastic opening tool. Remove the battery by prying up with your fingers or a plastic opening tool.
  • Remove the battery by prying up with your fingers or a plastic opening tool.

Add Comment

Locate the LCD cable connector and gently pry it directly up with a spudger. Locate the LCD cable connector and gently pry it directly up with a spudger.
  • Locate the LCD cable connector and gently pry it directly up with a spudger.

Add Comment

Remove the 5 ribbon cables. use the tip of the spudger to flip up the retaining flap, making sure to lift on the hinge and not the connector itself, then remove the cable from the connector. The flaps and connectors vary in color. Once the hinge has been lifted, the ribbon cable should take no force to remove.
  • Remove the 5 ribbon cables. use the tip of the spudger to flip up the retaining flap, making sure to lift on the hinge and not the connector itself, then remove the cable from the connector.

    • The flaps and connectors vary in color.

  • Once the hinge has been lifted, the ribbon cable should take no force to remove.

I would recommend putting some double sided padded tape above the connector labeled MB once you get the connector back on - that's the infamous touchscreen cable that comes loose once in awhile. This will effectively wedge the cable in place and keep it from falling out.

Kevin Kwan - Reply

Remove the 3 antenna cables using the tweezers by slowly pulling up. We found that pulling up and twisting a bit works best.
  • Remove the 3 antenna cables using the tweezers by slowly pulling up.

  • We found that pulling up and twisting a bit works best.

Add Comment

Remove the 4 1.6mm screws with a J0 head. Remove the 4 1.6mm screws with a J0 head.
  • Remove the 4 1.6mm screws with a J0 head.

Add Comment

Remove the red and black cable using the tweezers by gently pulling the connector to the right. Remove the red and black cable using the tweezers by gently pulling the connector to the right.
  • Remove the red and black cable using the tweezers by gently pulling the connector to the right.

Add Comment

Lift the motherboard out of the tablet's case.
  • Lift the motherboard out of the tablet's case.

Add Comment

Free the rubber housing around the camera by gently prying up with the spudger. Remove the rubber housing from the camera with tweezers.
  • Free the rubber housing around the camera by gently prying up with the spudger.

  • Remove the rubber housing from the camera with tweezers.

Add Comment

Remove the camera by carefully prying it out with the spudger. Remove the camera by carefully prying it out with the spudger.
  • Remove the camera by carefully prying it out with the spudger.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Diana Chiu

Member since: 07/14/2014

602 Reputation

4 Guides authored

Team

iFixit Member of iFixit

Community

129 Members

6,417 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 2

Past 30 Days: 12

All Time: 337