Introduction

This guide is meant to teach reader to install a new LCD screen. If the current LCD screen is broken or cracked LCD screen, this guide will help the reader to replace it with a new one.

Parts

No parts required.

Flip the camera over so the bottom is facing you. Flip the camera over so the bottom is facing you.
  • Flip the camera over so the bottom is facing you.

Add Comment

Open the cover on the bottom by sliding it in the direction of the arrow. Open the cover on the bottom by sliding it in the direction of the arrow.
  • Open the cover on the bottom by sliding it in the direction of the arrow.

Add Comment

Remove the batteries by pulling up on the top with your fingers.
  • Remove the batteries by pulling up on the top with your fingers.

Add Comment

Unless otherwise stated, use a phillips #00 screwdriver to remove screws.
  • Unless otherwise stated, use a phillips #00 screwdriver to remove screws.

  • Remove the two 4.70mm screws in the bottom of the plastic casing.

Add Comment

Remove the four 4.70mm screws in the left side of the camera. Remove the four 4.70mm screws in the left side of the camera.
  • Remove the four 4.70mm screws in the left side of the camera.

Add Comment

Now on the side with the strap, remove the other four 4.70mm screws. Now on the side with the strap, remove the other four 4.70mm screws.
  • Now on the side with the strap, remove the other four 4.70mm screws.

Add Comment

Deck the Halls
With tools and Fix Kits
Use your thumbs to pry the case apart. It is easiest to pry to case apart if your start at the bottom. The case should come apart with minimal effort. If  it doesn't, you can use a tool such as a Spudger or Plastic Opening tool.
  • Use your thumbs to pry the case apart.

  • It is easiest to pry to case apart if your start at the bottom.

  • The case should come apart with minimal effort. If it doesn't, you can use a tool such as a Spudger or Plastic Opening tool.

Add Comment

This step requires a significant amount of force.
  • This step requires a significant amount of force.

  • Pull the bottom half of the inner camera out of case about half an inch. This may be difficult and force is necessary.

Add Comment

While pulling the camera out of the case, note the small soft plastic cover on the side of the camera. This cover will detach from the rest of the device. Once the bottom of the inner camera is pulled out about an inch and a half, pull the device out completely.
  • While pulling the camera out of the case, note the small soft plastic cover on the side of the camera. This cover will detach from the rest of the device.

  • Once the bottom of the inner camera is pulled out about an inch and a half, pull the device out completely.

  • When completely removing the device from the case, use a firm grasp with your hands for stability and control.

Add Comment

Turn the camera so that the LCD screen is facing you.
  • Turn the camera so that the LCD screen is facing you.

  • If case is still on, remove it by following the Plastic Casing Installation Guide found in the previous steps.

  • You will not be able to complete this guide without removing the casing completely.

Add Comment

Remove the four 4.40mm screws that hold the LCD screen in place to the frame. Remove the four 4.40mm screws that hold the LCD screen in place to the frame.
  • Remove the four 4.40mm screws that hold the LCD screen in place to the frame.

Add Comment

Allow the LCD screen to flip down. This will expose the electric strip connecting the screen to the camera.
  • Allow the LCD screen to flip down. This will expose the electric strip connecting the screen to the camera.

Add Comment

Look for where the yellow electric strip is attached to the camera. There is a plastic grey bar and a white base holding this strip in place.
  • Look for where the yellow electric strip is attached to the camera. There is a plastic grey bar and a white base holding this strip in place.

  • Push the grey bar away from the white base. This will release the yellow electric strip and free the LCD screen from the camera.

Add Comment

Unplug the connected red and white wires. They will come out with the small white casing.
  • Unplug the connected red and white wires. They will come out with the small white casing.

Add Comment

Flip camera so that the lens is facing away from you. You should be looking at the LCD screen.
  • Flip camera so that the lens is facing away from you. You should be looking at the LCD screen.

Add Comment

Remove bottom left LCD mounting frame screw. Remove LCD screen from camera. Screen should come loose after screw is removed. Make sure electric strip comes out with screen.
  • Remove bottom left LCD mounting frame screw.

  • Remove LCD screen from camera. Screen should come loose after screw is removed. Make sure electric strip comes out with screen.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Nick Oleskowicz

Member since: 04/03/2012

227 Reputation

3 Guides authored

Team

Cal Poly, Team 15-13, Forte Spring 2012 Member of Cal Poly, Team 15-13, Forte Spring 2012

CPSU-FORTE-S12S15G13

5 Members

5 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 1

Past 30 Days: 12

All Time: 1,705