HTC Vive Sensor Array Assembly Replacement

Written By: Caleb Watts (and 6 other contributors)

Comments: 7
Favorites: 0
Completions: 1

HTC Vive Sensor Array Assembly Replacement

Difficulty

Moderate

Steps

Time Required

7 - 10 minutes

Introduction

The HTC Vive's sensor array may not track your movements even when the rest of the device appears to be functional. This guide will show you how to replace the Vive's sensor array assembly.

Tools

Buy these tools

Parts

Buy these parts

HTC Vive Sensor Array

$59.99

Buy

Step 1 Straps and Cables

Slide the HTC panel covering the cables forward, away from the Vive.

Gently pull on each of the four connectors to remove the sound and Three-in-One cables.

Slide the HTC panel covering the cables forward, away from the Vive.
Gently pull on each of the four connectors to remove the sound and Three-in-One cables.

Edit

Step 2

Undo the hook and loop tape on the straps.

Undo the hook and loop tape on the straps.
Slide the ends of the straps through the hinge loops.

Edit

Step 3 Facerest

Pull the facerest cushion off away from the Vive, separating the hook and loop tape.

Pull the facerest cushion off away from the Vive, separating the hook and loop tape.

Edit

Step 4

Use a T6 Torx Screwdriver to remove either of the two 12mm hinge screws holding the two hinges in place.

Allow the hinge to fall away once the screw is removed.

Use a T6 Torx Screwdriver to remove either of the two 12mm hinge screws holding the two hinges in place.
Allow the hinge to fall away once the screw is removed.
Repeat for the opposite side.

Edit

Step 5

Slide the plastic facerest away from the device.

Slide the plastic facerest away from the device.

Edit

Step 6 Outer Shell

Orient the Vive so that the camera is facing towards you and the connector ports are facing upwards.

There are four screws you need to remove that are covered with small black stickers (two on top, two on bottom).

Use a plastic opening tool to gently pry up the left side of the outer sheath.

Orient the Vive so that the camera is facing towards you and the connector ports are facing upwards.
There are four screws you need to remove that are covered with small black stickers (two on top, two on bottom).
Use a plastic opening tool to gently pry up the left side of the outer sheath.
If the left sheath is glued down, slide your plastic opening tool along the middle seam to break the bond.
Slide the left side of the sheath outwards.

Edit

Step 7

Slide a plastic opening tool underneath the right side of the sheath to remove any remaining glue.

Using the plastic opening tool, pry the right side of the sheath upwards slightly.

Using your hands, slide the right side of the sheath outwards.

Slide a plastic opening tool underneath the right side of the sheath to remove any remaining glue.
Using the plastic opening tool, pry the right side of the sheath upwards slightly.
Using your hands, slide the right side of the sheath outwards.

Edit

Step 8 Sensor Array Assembly

Remove the five 4mm Philips #00 screws holding the sensor array to the motherboard.

Remove the two 4mm Philips #00 screws holding the sensor array to the midframe.

Remove the five 4mm Philips #00 screws holding the sensor array to the motherboard.
Remove the two 4mm Philips #00 screws holding the sensor array to the midframe.

Edit

Step 9

Using a pair of ESD safe tweezers, gently pull the four ribbon cables out horizontally from the sensor array.

Using a pair of ESD safe tweezers, gently pull the four ribbon cables out horizontally from the sensor array.

Edit

Step 10

Be careful not to lift the sensor array too far from the rest of the device because the camera ribbon cable may tear.

Lift the sensor array away from the rest of the Vive until the camera cable tugs back and hold it in place.

The camera ribbon cable must be pulled out of its socket vertically, as opposed to all other ribbon cables which slide out horizontally.

Be careful not to lift the sensor array too far from the rest of the device because the camera ribbon cable may tear.
Lift the sensor array away from the rest of the Vive until the camera cable tugs back and hold it in place.
The camera ribbon cable must be pulled out of its socket vertically, as opposed to all other ribbon cables which slide out horizontally.
Disconnect the camera by lifting its ribbon cable up and away from the motherboard using a pair of ESD safe tweezers.
Lift the sensor array upwards away from the motherboard to separate the array from the device fully.