HP Pavilion 14-b015dx Keyboard Replacement

You're viewing a previously published version of this guide. View latest version

Dec 22, 2017 - 03:00:44

Dec 22, 2017 - 03:00:44 Dec 22, 2017 - 02:44:45 Dec 22, 2017 - 02:44:43 Dec 22, 2017 - 02:44:35 Dec 22, 2017 - 02:42:08 Dec 11, 2017 - 05:14:13 Dec 11, 2017 - 05:03:25 Dec 11, 2017 - 05:03:16 Dec 11, 2017 - 05:01:26 Dec 11, 2017 - 05:00:01 Dec 11, 2017 - 04:20:34 Dec 11, 2017 - 04:20:13 Dec 11, 2017 - 04:19:17 Dec 11, 2017 - 04:18:57 Dec 10, 2017 - 06:30:11 Dec 10, 2017 - 02:17:40 Nov 29, 2017 - 07:38:48 Nov 26, 2017 - 03:44:50 Nov 26, 2017 - 02:46:11 Nov 26, 2017 - 02:44:48 Nov 26, 2017 - 02:42:51 Nov 26, 2017 - 02:42:39 Nov 20, 2017 - 06:32:53 Nov 20, 2017 - 06:32:00 Nov 20, 2017 - 06:31:48 Nov 20, 2017 - 06:31:20 Nov 20, 2017 - 06:26:45 Nov 20, 2017 - 06:25:15 Nov 20, 2017 - 06:24:44 Nov 20, 2017 - 06:24:30 Nov 20, 2017 - 06:17:21 Nov 20, 2017 - 06:14:44 Nov 20, 2017 - 06:12:47 Nov 20, 2017 - 06:12:06 Nov 20, 2017 - 06:07:04 Nov 13, 2017 - 06:47:29 Nov 13, 2017 - 06:43:41 Nov 13, 2017 - 06:43:00

Newer

Introduction

This guide can be used to replace the keyboard in your HP Pavilion 14-b015dx Laptop.

What you need

Step 1 Battery

HP Pavilion 14-b015dx Keyboard Replacement, Battery: step 1, image 1 of 1

Make sure the computer is completely powered down and unplug the power cord.

Step 2

Place the device on your work surface with bottom facing up and the battery located at the top.

Step 3

Slide the left release tab toward the center of the computer to the unlock position. Next slid the right tab toward the center of the computer and hold it there while completing step 4.

Step 4

Remove the battery by sliding it upwards and away from the computer.

Step 5 Keyboard

HP Pavilion 14-b015dx Keyboard Replacement, Keyboard: step 5, image 1 of 1

Unscrew the ten 6.0 mm Philips head screws on the base of the device with a Phillips #0 head screwdriver.

Step 6

Insert the plastic opening tool between the keyboard and the plastic housing.
Pry the keyboard upward away from the device.
Move the tool around the edge of the entire keyboard while continuing to pry.
You will hear the clips pop once you have released them.

Step 7

Once you have released all of the clips, slowly lift the keyboard exposing the ribbon cable.
Lift the tab on the keyboard ZIF connector with a plastic opening tool and gently remove the ribbon cable.