Fix Your Stuff Community Store

Etekcity Lasergrip 1080 Screen Replacement

Introduction

This guide will show you how to replace a faulty screen. This will use a screwdriver and a plastic opening tool. There are no hazards involved with this guide.

What you need

  1. Etekcity Lasergrip 1080 Screen Replacement, Battery: step 1, image 1 of 1

    • Pull the battery cover away from the handle by gripping near the thumb groove.

    Edit

  2. Etekcity Lasergrip 1080 Screen Replacement: step 2, image 1 of 1

    • Gently pull the battery out of the handle.

    • Excessive force could damage wires.

    Edit

  3. Etekcity Lasergrip 1080 Screen Replacement: step 3, image 1 of 2 Etekcity Lasergrip 1080 Screen Replacement: step 3, image 2 of 2

    • Disconnect the battery by pulling the connector away from it.

    • Positive first

    • Negative second

    • When replacing the battery, this order is reversed.

    Edit

  4. Etekcity Lasergrip 1080 Screen Replacement, Buttons: step 4, image 1 of 2 Etekcity Lasergrip 1080 Screen Replacement, Buttons: step 4, image 2 of 2

    • Remove the battery cover from the device by pulling it straight out.

    Edit

  6. Etekcity Lasergrip 1080 Screen Replacement: step 5, image 1 of 2 Etekcity Lasergrip 1080 Screen Replacement: step 5, image 2 of 2

    • Using the plastic opening tool remove the front and rear yellow covers.

    • When removing the back cover, be careful not to lose the buttons as they are not connected.

    Edit

  7. Etekcity Lasergrip 1080 Screen Replacement: step 6, image 1 of 1

    • Remove the two 3.1 mm Phillips #0 screws.

    Edit

  8. Etekcity Lasergrip 1080 Screen Replacement: step 7, image 1 of 2 Etekcity Lasergrip 1080 Screen Replacement: step 7, image 2 of 2

    • Pull the two halves apart.

    • Be careful not to lose any components on the inside.

    Edit

  9. Etekcity Lasergrip 1080 Screen Replacement: step 8, image 1 of 1

    • Realign the buttons with the button terminals.

    • Red terminal to red button.

    • Orange terminal to orange button.

    • Yellow terminal to yellow button.

    Edit

  10. Etekcity Lasergrip 1080 Screen Replacement, Etekcity Lasergrip 1080 Trigger Replacement: step 9, image 1 of 2 Etekcity Lasergrip 1080 Screen Replacement, Etekcity Lasergrip 1080 Trigger Replacement: step 9, image 2 of 2

    • Carefully pull the trigger out.

    • The trigger is spring loaded, so be careful that you do not lose the spring as you pull the trigger out.

    • To put the trigger back in, align the peg with the hole in the handle and align the shaft with the button terminal.

    Edit

  11. Etekcity Lasergrip 1080 Screen Replacement, Screen: step 10, image 1 of 1

    • Carefully pull the motherboard out of its slot in the body of the device.

    Edit

  12. Etekcity Lasergrip 1080 Screen Replacement: step 11, image 1 of 2 Etekcity Lasergrip 1080 Screen Replacement: step 11, image 2 of 2

    • Unscrew the two 3.4 mm screws on the motherboard.

    Edit

  13. Etekcity Lasergrip 1080 Screen Replacement: step 12, image 1 of 1

    • Take off the cover and separate the parts.

    • All of these parts are fragile and mishandling them may cause damage.

    Edit
Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

with 2 other contributors

Carlos Pineda

Member since: 08/27/15

195 Reputation

1 Guide authored

Badges: 5

+2 more badges

Team

USF Tampa, Team 5-1, Blackwell Fall 2015 Member of USF Tampa, Team 5-1, Blackwell Fall 2015

USFT-BLACKWELL-F15S5G1

3 Members

9 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 7

Past 30 Days: 10

All Time: 909