Introduction

Backup all important data files on the system.
Remember opening your laptop may void the warranty, so perform this at your own risk and our help.

Image 1/3: Unplug the charger and remove the battery. Image 2/3: Remove the battery by sliding the lock tab (outlined in red) and use the other hand to remove the battery. Image 3/3: Remove the battery by sliding the lock tab (outlined in red) and use the other hand to remove the battery.
  • Perform a complete system backup and shutdown the computer.

  • Unplug the charger and remove the battery.

  • Remove the battery by sliding the lock tab (outlined in red) and use the other hand to remove the battery.

Add Comment

Image 1/1: Locate and remove three phillips head screws. These screws measure 3.55mm in length and 2.93mm in width with a fine thread.
  • Remove the hard drive

  • Locate and remove three phillips head screws. These screws measure 3.55mm in length and 2.93mm in width with a fine thread.

  • Remove the hard drive and set it aside trying not to touch anything but the grey plastic grip pad. Doing so may cause damage to your hard drive.

Add Comment

Image 1/3: There may be a little resistance pulling it out. Image 2/3: There may be a little resistance pulling it out. Image 3/3: There may be a little resistance pulling it out.
  • Remove the CD/DVD Drive by pushing on the button under the drive.

  • There may be a little resistance pulling it out.

Add Comment

Image 1/1:
  • Remove the 14 Phillips screws from the bottom of the laptop.

Two additional screws not circled need to be removed. One in the upper left (near the foot and circled screw), and one in lower center (at bottom right of RAM, end of STRIKE ZONE wording).

False Precision - Reply

Image 1/2: Using a Plastic Pry tool carefully pry off the keyboard bezel keeping in mind '''wires are attached''' so do not pull too far or hard. Image 2/2: Using a Plastic Pry tool carefully pry off the keyboard bezel keeping in mind '''wires are attached''' so do not pull too far or hard.
  • Flip the laptop face up making sure the screen is opened all the way and is flat as shown in the first picture.

  • Using a Plastic Pry tool carefully pry off the keyboard bezel keeping in mind wires are attached so do not pull too far or hard.

Add Comment

Image 1/2: Remove the ribbon from the laptop motherboard, this will allow you to set the keyboard aside. Image 2/2: Remove the ribbon from the laptop motherboard, this will allow you to set the keyboard aside.
  • Now, remove the keyboard screws then the keyboard. There is a ribbon cable (wires) attached to bottom, be careful not to tear it.

  • Remove the ribbon from the laptop motherboard, this will allow you to set the keyboard aside.

Add Comment

Image 1/3: Image 2/3: Image 3/3:
  • Remove the memory chip under the keyboard by pulling the two tabs away from each other as shown in second picture. (Yes there is one on the bottom as well)

Add Comment

Image 1/1: Push the retaining tab  and lift the card out.
  • Disconnect the wireless card from the bottom-corner.

  • Push the retaining tab and lift the card out.

  • Do this for the ethernet card which is in the same spot.

Add Comment

Image 1/1: Remove the cable that connects the track pad (large rectangle) to frame by pulling straight out.  The cable is also located to the left of DDR2 DIMM A.
  • Remove the cable that connects the speaker (small rectangle) to the frame by pulling straight out. The cable is located to the left of DDR2 DIMM A.

  • Remove the cable that connects the track pad (large rectangle) to frame by pulling straight out. The cable is also located to the left of DDR2 DIMM A.

Add Comment

Image 1/3: Remove the upper casing from the bottom casing. Image 2/3: *note– when prying shell from laptop – gently pry open 3 tabs by the CD-ROM with spudger. Image 3/3: *note– when prying shell from laptop – gently pry open 3 tabs by the CD-ROM with spudger.
  • Remove 3 Screws that hold the upper case to the mother board.

  • Remove the upper casing from the bottom casing.

  • *note– when prying shell from laptop – gently pry open 3 tabs by the CD-ROM with spudger.

Between steps 8 and 10, the display must be removed; you'll note in step 10's picture that the display isn't there.

1. Detach the ribbon cable that connects the display to the motherboard.

2. Move the display cable and WLAN cable so they don't get caught.

3. Unscrew the two screws in back

4. Lift the display's hinges out of the main assembly.

False Precision - Reply

Image 1/3: Unscrew 6 spring loaded screws from Heat Sink. These are permanently attached to heat sink and will not come off. Image 2/3: Unscrew 6 spring loaded screws from Heat Sink. These are permanently attached to heat sink and will not come off. Image 3/3: Unscrew 6 spring loaded screws from Heat Sink. These are permanently attached to heat sink and will not come off.
  • Remove 2 screws for fan removal – both 5.6 mm length x 2.31 mm width – remove the fan power cable.

  • Unscrew 6 spring loaded screws from Heat Sink. These are permanently attached to heat sink and will not come off.

Add Comment

Image 1/3: 3 of the screws are 3.80mm length x 1.89mm width. One of these is near top left of Dell MCIA. The other is near top left of WWAN. An there is one underneath the Black WWAN label. Image 2/3: Remove the PCMCIA connector from the motherboard. Image 3/3: Turn the laptop on the side and remove 2 female hex screws from video card and 2 posts from serial port using socket driver (3/16 socket) All hex screws are 10.23mm x 2.66mm size
  • There are 7 screws that need to be removed around edge of Motherboard. 4 of the screws are 3.73mm length x 1.90mm width

  • 3 of the screws are 3.80mm length x 1.89mm width. One of these is near top left of Dell MCIA. The other is near top left of WWAN. An there is one underneath the Black WWAN label.

  • Remove the PCMCIA connector from the motherboard.

  • Turn the laptop on the side and remove 2 female hex screws from video card and 2 posts from serial port using socket driver (3/16 socket) All hex screws are 10.23mm x 2.66mm size

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

7 other people completed this guide.

Henry

Member since: 09/02/2014

1,035 Reputation

4 Guides authored

Team

Pasco Hernando, Team 1-2, Prince Fall 2014 Member of Pasco Hernando, Team 1-2, Prince Fall 2014

PHSC-PRINCE-F14S1G2

10 Members

7 Guides authored

One Comment

I'm so glad I found this. I'm gonna ATTEMPT to fix ours when we get everything in. I have this saved so I can easily find it. I will let you know how it goes after I'm done. GREAT BIG HUGE THANKS again and wish me luck. :D

pambi43 - Reply

Add Comment

View Statistics:

Past 24 Hours: 3

Past 7 Days: 17

Past 30 Days: 75

All Time: 2,761