Introduction

This replacement guide shows how to remove the device's daughter board, also known as the mother board extension located on the front side of the camera. The front panel must be removed before hand.

Tools

No tools required.

Parts

No parts required.

Squeeze the eyepiece between your index finger and thumb and lift up and off
  • Squeeze the eyepiece between your index finger and thumb and lift up and off

Add Comment

Using the PH000 screwdriver head, remove the four 4 mm screws on the bottom of the camera
  • Using the PH000 screwdriver head, remove the four 4 mm screws on the bottom of the camera

Add Comment

On the right side of the camera (from the LCD screen), use the PH000 screwdriver head to remove the two 3mm screws
  • On the right side of the camera (from the LCD screen), use the PH000 screwdriver head to remove the two 3mm screws

Add Comment

Remove grip by slowly peeling off
  • Remove grip by slowly peeling off

Add Comment

Using the PH000 screwdriver, remove the four 4mm screws behind the eyepiece
  • Using the PH000 screwdriver, remove the four 4mm screws behind the eyepiece

Add Comment

On the left side of the camera (from the LCD screen), use the PH000 screwdriver head to remove one 4 mm screw
  • On the left side of the camera (from the LCD screen), use the PH000 screwdriver head to remove one 4 mm screw

Add Comment

Black Friday
Broken doesn't stand a chance.
Remove side panel by lifting off with fingers
  • Remove side panel by lifting off with fingers

Add Comment

Use hands to pry off the back panel
  • Use hands to pry off the back panel

Add Comment

Using the PH000 screwdriver head, remove the four 3mm screws on the front
  • Using the PH000 screwdriver head, remove the four 3mm screws on the front

Add Comment

Remove front grip by gently peeling from the edge towards the center of the camera
  • Remove front grip by gently peeling from the edge towards the center of the camera

Add Comment

Using the PH000 screwdriver head, unscrew the 3 mm screw that was under the grip
  • Using the PH000 screwdriver head, unscrew the 3 mm screw that was under the grip

Add Comment

Using the PH000 screwdriver, remove the 4mm screw at the bottom of the camera
  • Using the PH000 screwdriver, remove the 4mm screw at the bottom of the camera

Add Comment

Remove the front panel by using tweezers to pry the panel over the metal ring protrusion Remove the front panel by using tweezers to pry the panel over the metal ring protrusion Remove the front panel by using tweezers to pry the panel over the metal ring protrusion
  • Remove the front panel by using tweezers to pry the panel over the metal ring protrusion

Add Comment

Using the PH000 screwdriver head, remove the three 3mm screws
  • Using the PH000 screwdriver head, remove the three 3mm screws

Add Comment

Carefully remove the cable from its plastic base with fingers
  • Carefully remove the cable from its plastic base with fingers

Add Comment

Gently slide board out with thumb
  • Gently slide board out with thumb

Add Comment

Gently disconnect cable by pulling out from plastic base with fingers
  • Gently disconnect cable by pulling out from plastic base with fingers

Add Comment

Disconnect cables by pulling out from base with fingers
  • Disconnect cables by pulling out from base with fingers

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

One other person completed this guide.

Erik Mork

Member since: 01/27/2017

530 Reputation

5 Guides authored

Team

Cal Poly, Team 22-10, Maness Winter 2017 Member of Cal Poly, Team 22-10, Maness Winter 2017

CPSU-MANESS-W17S22G10

4 Members

5 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 2

Past 7 Days: 4

Past 30 Days: 26

All Time: 154