Black and Decker BV2500 Type 4 Impellor (Fan) Replacement

You're viewing a previously published version of this guide. View latest version

Jun 18, 2015 - 02:53:05

Jun 18, 2015 - 02:53:05 Mar 18, 2014 - 02:17:28 Mar 18, 2014 - 02:17:22 Mar 07, 2014 - 03:36:12 Mar 07, 2014 - 03:31:12 Mar 01, 2014 - 01:57:50 Mar 01, 2014 - 01:57:34 Mar 01, 2014 - 01:56:11 Feb 26, 2014 - 09:53:24 Feb 26, 2014 - 09:52:16 Feb 26, 2014 - 09:52:01 Feb 26, 2014 - 06:56:15 Feb 26, 2014 - 03:39:37 Feb 26, 2014 - 03:14:06 Feb 26, 2014 - 03:13:50 Feb 26, 2014 - 03:13:20 Feb 26, 2014 - 03:12:59 Feb 24, 2014 - 09:55:09 Feb 24, 2014 - 09:55:04 Feb 24, 2014 - 09:54:56 Feb 24, 2014 - 09:53:22 Feb 24, 2014 - 09:52:51 Feb 24, 2014 - 09:52:37 Feb 24, 2014 - 09:48:38 Feb 24, 2014 - 09:48:28 Feb 24, 2014 - 09:25:23 Feb 23, 2014 - 07:59:53 Feb 23, 2014 - 07:58:33 Feb 23, 2014 - 07:57:48 Feb 23, 2014 - 07:55:38 Feb 23, 2014 - 07:54:04 Feb 23, 2014 - 03:41:03 Feb 23, 2014 - 03:18:56 Feb 23, 2014 - 03:18:40 Feb 23, 2014 - 02:52:32 Feb 23, 2014 - 02:47:33 Feb 23, 2014 - 02:47:10 Feb 23, 2014 - 02:46:53 Feb 23, 2014 - 02:43:42 Feb 23, 2014 - 02:42:23 Feb 23, 2014 - 02:36:15 Feb 20, 2014 - 09:56:23 Feb 20, 2014 - 09:54:54 Feb 20, 2014 - 09:52:15 Feb 20, 2014 - 09:48:39 Feb 20, 2014 - 09:47:40 Feb 20, 2014 - 09:40:34 Feb 20, 2014 - 09:37:38 Feb 20, 2014 - 09:36:13 Feb 20, 2014 - 09:34:11 Feb 20, 2014 - 09:33:06 Feb 20, 2014 - 09:29:30 Feb 10, 2014 - 09:58:37 Feb 10, 2014 - 09:57:47 Feb 10, 2014 - 09:53:15 Feb 10, 2014 - 09:45:02 Feb 09, 2014 - 01:25:13 Feb 09, 2014 - 01:18:56

Newer

Introduction

This guide will take you through the process of replacing the impeller on the Black and Decker BV2500 Type 4.

What you need

Step 1 Clamshell (Black Outer Casing)

Black and Decker BV2500 Type 4 Impellor (Fan) Replacement, Clamshell (Black Outer Casing): step 1, image 1 of 1

Using a Phillips #2 screwdriver, remove the six 20 mm screws in the black plastic casing (clamshell).

Step 2

Using your hands, remove the blower tube and clamshell.
To remove the clamshell, pull apart starting from the bottom until it is pulled out from the notches. Then slide it out away from the device.

Step 3 Impellor (Fan)

Black and Decker BV2500 Type 4 Impellor (Fan) Replacement, Impellor (Fan): step 3, image 1 of 2

Black and Decker BV2500 Type 4 Impellor (Fan) Replacement, Impellor (Fan): step 3, image 2 of 2

Locate and unscrew the ten 20 mm Phillips #2 screws in the orange casing with a Phillips #2 screwdriver.
Using your hands, lift off the side of the orange casing with the screws facing you.

Step 4

Locate the fan.
Unscrew the 9/16" cap and nut (in the middle of the fan) with the ratcheting socket wrench.

Step 5

Carefully use your hands to slide the fan out from the rest of the device.
Be careful to not lose the washer when you slide out the fan. You need it when reassembling the device.