Introduction

This guide will help you replace the display of your Acer Aspire One 751h-1948.

Close the laptop and flip it over to view the back of the laptop.
  • Close the laptop and flip it over to view the back of the laptop.

Add Comment

Unlock the right side of the battery by sliding the battery lock to the right. Then slide the left lock to the left and remove the battery. Unlock the right side of the battery by sliding the battery lock to the right. Then slide the left lock to the left and remove the battery. Unlock the right side of the battery by sliding the battery lock to the right. Then slide the left lock to the left and remove the battery.
  • Unlock the right side of the battery by sliding the battery lock to the right. Then slide the left lock to the left and remove the battery.

Add Comment

Unscrew the two Phillips #0 (M2-L2.5 mm) holding down the network card panel. These screws don't come all the way out.
  • Unscrew the two Phillips #0 (M2-L2.5 mm) holding down the network card panel.

  • These screws don't come all the way out.

Add Comment

Unplug the two connecting cables by lifting them up. They should unclip easily. Unplug the two connecting cables by lifting them up. They should unclip easily. Unplug the two connecting cables by lifting them up. They should unclip easily.
  • Unplug the two connecting cables by lifting them up. They should unclip easily.

Add Comment

Remove the screw Phillips #0 (M2-L3 mm) holding down the network card. Pull out the card. Remove the screw Phillips #0 (M2-L3 mm) holding down the network card. Pull out the card. Remove the screw Phillips #0 (M2-L3 mm) holding down the network card. Pull out the card.
  • Remove the screw Phillips #0 (M2-L3 mm) holding down the network card. Pull out the card.

Add Comment

Black Friday
Broken doesn't stand a chance.
Unscrew the Phillips 0# (M2 L2.5 mm) screw and remove the cover panel.
  • Unscrew the Phillips 0# (M2 L2.5 mm) screw and remove the cover panel.

  • These screws will not come out all the way.

Add Comment

Remove the hard drive by sliding it to the left and pull it out. Remove the hard drive by sliding it to the left and pull it out. Remove the hard drive by sliding it to the left and pull it out.
  • Remove the hard drive by sliding it to the left and pull it out.

Add Comment

Unscrew the Phillips #0 (M2-L2.5 mm) screws. Unscrew the Phillips #0 (M2-L2.5 mm) screws.
  • Unscrew the Phillips #0 (M2-L2.5 mm) screws.

Add Comment

Use the plastic opening tool to push in each of the four clips and carefully lift the keyboard. Don't lift the keyboard completely so that you don't damage the ribbon cable underneath. Don't lift the keyboard completely so that you don't damage the ribbon cable underneath.
  • Use the plastic opening tool to push in each of the four clips and carefully lift the keyboard.

  • Don't lift the keyboard completely so that you don't damage the ribbon cable underneath.

Add Comment

When you remove the keyboard, be careful not to damage the ribbon cable that attaches it to the motherboard. Unplug the ribbon cable by gently lifting the black tab up. Then remove the cable.
  • When you remove the keyboard, be careful not to damage the ribbon cable that attaches it to the motherboard.

  • Unplug the ribbon cable by gently lifting the black tab up. Then remove the cable.

Add Comment

Unplug the SCD cable Unplug the SCD cable Unplug the SCD cable
  • Unplug the SCD cable

Add Comment

Use the spudger to remove all rubber pads covering the screws for the upper casing. Then unscrew all the Phillips #0 (M2-L5 mm) screws under rubber pads.
  • Use the spudger to remove all rubber pads covering the screws for the upper casing.

  • Then unscrew all the Phillips #0 (M2-L5 mm) screws under rubber pads.

Add Comment

Separate the upper casing from the display. Separate the upper casing from the display. Separate the upper casing from the display.
  • Separate the upper casing from the display.

Add Comment

Unscrew all the Phillips 0# (M2-L2.5 mm) on each side of the display. Unscrew all the Phillips 0# (M2-L2.5 mm) on each side of the display. Unscrew all the Phillips 0# (M2-L2.5 mm) on each side of the display.
  • Unscrew all the Phillips 0# (M2-L2.5 mm) on each side of the display.

Add Comment

Separate the screen from the metal frame that secures it to the upper casing and remove the screen.
  • Separate the screen from the metal frame that secures it to the upper casing and remove the screen.

  • Be careful, the display is very sensitive.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Chris Bolton

Member since: 03/22/2017

422 Reputation

4 Guides authored

Team

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 1

Past 30 Days: 2

All Time: 51