Skip to main content

Introduction

Use this guide to help you remove the broken or defected motherboard in your Sony Handycam HDR-Cx220.

  1. Push in the battery indicator.
    • Push in the battery indicator.

  2. Slide the battery out of the slot.
    • Slide the battery out of the slot.

    • To put the battery back in, line up the battery's metal part with the camera's and slide it in.

  3. Use the Phillips #0 screwdriver to remove the two 5mm screws. Use the Phillips #0 screwdriver to remove the two 5mm screws. Use the Phillips #0 screwdriver to remove the three 5mm screws.
    • Use the Phillips #0 screwdriver to remove the two 5mm screws.

    • Use the Phillips #0 screwdriver to remove the two 5mm screws.

    • Use the Phillips #0 screwdriver to remove the three 5mm screws.

  4. Use the plastic opening tool to loosen the plastic case of the camcorder. Use the plastic opening tool to loosen the plastic case of the camcorder. Use the plastic opening tool to loosen the plastic case of the camcorder.
    • Use the plastic opening tool to loosen the plastic case of the camcorder.

  5. Use your hands to remove the plastic case.
    • Use your hands to remove the plastic case.

    • Gently pull on the case not to damage anything internally.

  6. MacBook Battery Fix Kits

    Starting at $69.99

    Buy Now

    MacBook Battery Fix Kits

    Starting at $69.99

    Buy Now
  7. Use the Phillips #0 Screwdriver to remove the 5mm screw Use the Phillips #0 Screwdriver to remove the 5mm screw Use the Plastic Opening tools to unhook the highlighted area.
    • Use the Phillips #0 Screwdriver to remove the 5mm screw

    • Use the Phillips #0 Screwdriver to remove the 5mm screw

    • Use the Plastic Opening tools to unhook the highlighted area.

  8. Remove the 3 (4mm) screws on the front of the lens using the Philips #0 Screwdriver.
    • Remove the 3 (4mm) screws on the front of the lens using the Philips #0 Screwdriver.

  9. Remove the lens and clean it if needed.
    • Remove the lens and clean it if needed.

  10. Use the Phillips #0 Screwdriver to remove the shown 5mm screws. Use the plastic opening tool to release the front hook. Use the plastic opening tool to release the back hook.
    • Use the Phillips #0 Screwdriver to remove the shown 5mm screws.

    • Use the plastic opening tool to release the front hook.

    • Use the plastic opening tool to release the back hook.

  11. Gently pull on the 2 wires shown on the bottom of the camcorder. Disconnect the wire shows on the second picture.
    • Gently pull on the 2 wires shown on the bottom of the camcorder.

    • Disconnect the wire shows on the second picture.

  12. Use the Phillips #0 screwdriver to remove the 4mm screw shown. Gently remove the motherboard with your fingers.
    • Use the Phillips #0 screwdriver to remove the 4mm screw shown.

    • Gently remove the motherboard with your fingers.

  13. Remove the side wire from the motherboard as shown on the photo. Remove the top wire from the motherboard as shown on the photo.
    • Remove the side wire from the motherboard as shown on the photo.

    • Remove the top wire from the motherboard as shown on the photo.

  14. Unplug the speaker from the motherboard. Unplug the speaker from the motherboard.
    • Unplug the speaker from the motherboard.

Conclusion

To reassemble your device, follow these instructions in reverse order.

One other person completed this guide.

Keven

Member since: 03/11/2016

712 Reputation

6 Guides authored

Team

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 2

Past 30 Days: 9

All Time: 444