Skip to main content

Fix Your Stuff

Right to Repair

Store

Help

Current version by: gumbypokey1960 ,

Title:

coffee grounds into the area where the K Cup is

Text:

HI.  I have had same problem with my Model B60 refusing to close.

I'm not sure what happened with mine, but I ended up forcing it to close.

DO NOT DO THIS

Check near where the silver handle used to close  on the K Cup is attached to the machine.  Mine has 2 screws on the underside of the silver-colored handle which were loose.  They're located on underside of silver-colored handle which is used to close the machine to brew - very close to where handle attaches to the unit. Look for one screw on each side of silver handle - my machine has screws that required screwdriver bit CRV-T15.

Possibly these or some other screws have become loose not allowing things to line up properly & close completely.

Also, I looked carefully at the photos posted by both schmick & @oldturkey03.  I noticed schmick's photo of the needle on the top (center photo) appears to not have a black rubber washer or seal or whatever it is called, which I can see in photo posted by @oldturkey03 (3rd photo from top - 2nd to the last of photos-from top to bottom)

Hope I helped somebody

My Keuring Model B60 is currently spewing coffee grounds into K Cup area & a little into the cup, but still brews.

Not sure, but, I think my problem might be the following:  After it refused to close & I forced it to close it brewed but grounds were in cup & in machine.   I adjusted the silver-colored handle - screw had loosened. I also removed the black rubber washer or gasket.  I wasn't sure which way it went when I replaced the black rubber washer-thing, so I'm hoping it's upside-down????

Anybody have any ideas?????

Would be appreciated.  My machine brews fine, isn't slow or not filling the cup.  It's just getting the coffee grounds into the area where the K Cup is placed & also some grounds into the brewed coffee...

Thanks in advance

Device:

Keurig Elite

Status:

open

Accepted Answer:

257062

Edit by: oldturkey03 ,

Title:

No Title (You should edit this question)coffee grounds into the area where the K Cup is
No Title (You should edit this question)coffee grounds into the area where the K Cup is

Text:

HI.  I have had same problem with my Model B60 refusing to close.

I'm not sure what happened with mine, but I ended up forcing it to close.

DO NOT DO THIS

Check near where the silver handle used to close  on the K Cup is attached to the machine.  Mine has 2 screws on the underside of the silver-colored handle which were loose.  They're located on underside of silver-colored handle which is used to close the machine to brew - very close to where handle attaches to the unit. Look for one screw on each side of silver handle - my machine has screws that required screwdriver bit CRV-T15.

Possibly these or some other screws have become loose not allowing things to line up properly & close completely.

Also, I looked carefully at the photos posted by both schmick & @oldturkey03.  I noticed schmick's photo of the needle on the top (center photo) appears to not have a black rubber washer or seal or whatever it is called, which I can see in photo posted by @oldturkey03 (3rd photo from top - 2nd to the last of photos-from top to bottom)

Hope I helped somebody

My Keuring Model B60 is currently spewing coffee grounds into K Cup area & a little into the cup, but still brews.

Not sure, but, I think my problem might be the following:  After it refused to close & I forced it to close it brewed but grounds were in cup & in machine.   I adjusted the silver-colored handle - screw had loosened. I also removed the black rubber washer or gasket.  I wasn't sure which way it went when I replaced the black rubber washer-thing, so I'm hoping it's upside-down????

Anybody have any ideas?????

Would be appreciated.  My machine brews fine, isn't slow or not filling the cup.  It's just getting the coffee grounds into the area where the K Cup is placed & also some grounds into the brewed coffee...

Thanks in advance

Device:

Keurig Elite

Status:

open

Original post by: gumbypokey1960 ,

Title:

No Title (You should edit this question)

Text:

HI.  I have had same problem with my Model B60 refusing to close.

I'm not sure what happened with mine, but I ended up forcing it to close.

DO NOT DO THIS

Check near where the silver handle used to close  on the K Cup is attached to the machine.  Mine has 2 screws on the underside of the silver-colored handle which were loose.  They're located on underside of silver-colored handle which is used to close the machine to brew - very close to where handle attaches to the unit. Look for one screw on each side of silver handle - my machine has screws that required screwdriver bit CRV-T15.

Possibly these or some other screws have become loose not allowing things to line up properly & close completely.

Also, I looked carefully at the photos posted by both schmick & @oldturkey03.  I noticed schmick's photo of the needle on the top (center photo) appears to not have a black rubber washer or seal or whatever it is called, which I can see in photo posted by @oldturkey03 (3rd photo from top - 2nd to the last of photos-from top to bottom)

Hope I helped somebody

My Keuring Model B60 is currently spewing coffee grounds into K Cup area & a little into the cup, but still brews.

Not sure, but, I think my problem might be the following:  After it refused to close & I forced it to close it brewed but grounds were in cup & in machine.   I adjusted the silver-colored handle - screw had loosened. I also removed the black rubber washer or gasket.  I wasn't sure which way it went when I replaced the black rubber washer-thing, so I'm hoping it's upside-down????

Anybody have any ideas?????

Would be appreciated.  My machine brews fine, isn't slow or not filling the cup.  It's just getting the coffee grounds into the area where the K Cup is placed & also some grounds into the brewed coffee...

Thanks in advance

Device:

Keurig Elite

Status:

open