⟐ Answered July 05, 2026 at 16:38 MST

⟐ Answered July 05, 2026 at 11:55 MST

⟐ Commented July 04, 2026 at 23:59 MST

I would try to press drain/spin and it will only drain a bit and then not spin.

I have replaced the shift actuator, splutch kit, and capacitor(even though old one was good).

After replacing the parts I have done a recalibration and the issue still persisted.

I went into Diag mode and got a code F7E1 for Basket speed. During Auto test it went through it completely fine.

In manual mode it everything seems to work except for it being on "LowSpin/HighSpin" where I get nothing. Agitation mode works fine. The windings of the motor were in spec as I was going through trouble shooting steps.

I'm currently at the point where I'm trying to check voltage on J12 / J2 connector. My multimeter isn't thin enough to backprobe the 4 pin J12 connector.

What else can I do to fix this washer?

Also when roommates use the washer it's sometimes unbalanced and clunks until we stop the cycle and rebalance the load. Tub suspension bolts seem intact by the way

⟐ Commented July 03, 2026 at 21:51 MST

Translation Spanish → English

My washing machine stops, leaks water, and doesn't finish the cycle.

I've already tried opening up the control panel and cleaning it, but nothing worked.

⟐ Commented July 01, 2026 at 1:20 MST

LSN1000LW0

Washer recently started doing this thing where if agitates briefly then stops. The timer carries on through the cycle. It fills and spins fine. I did the unplug it technique a few times but never to could get it to agitate much longer than 30 seconds. It does this in all cycles types.

⟐ Answer accepted June 30, 2026 at 5:26 MST

⟐ Commented June 30, 2026 at 2:06 MST

I'm having a hard time finding an answer to this specific scenario. My Whirlpool washer model # WTW4815EW0, about 4 years old, recently stopped spinning out clothes at the end of a wash cycle. We use both the normal cycle and bulky items, and this occurs on both. The problem began gradually, only sometimes would the washer not spin out at the end of the cycle. Now it's every time. However, the strange part is that mechanically it has no issue spinning. After it decides to quit on the wash cycle (clothes are clean and tub drained, but still sopping wet), I just set it to drain and spin and it finishes the job without problem. So I don't think it's a lid latch, a belt, or anything that would stop it from spinning ever. What do I need to do to fix this? The washer was cheap to begin with and the cost of a repair person could easily cost as much as it did new, so if it's not something I can fix on my own I'll just get a new one. Thanks for any help.

I have some updated information. I ran some manual tests and found that the washer spins on low but not on high speed. The low speed test runs without issue. During the high speed test, the motor kicks in for just a second and then immediately quits, with lid lock light flashing. I performed a tachometer test which it also seemed to fail. I checked the belt underneath which looks good. Drive test performed good. Control board has no obvious damage.

⟐ Commented June 29, 2026 at 14:38 MST

Is this a motor that is going out or some kind of bearing? It runs fine but it gets REALLY loud during any spin cycle

⟐ Answered June 29, 2026 at 2:46 MST

N.B. the video I uploaded won't seem to play but this happens when the drum starts to move from side to side. The machine is generally only turning very gently at this point. Resubmitted as a YouTube upload.

⟐ Answer accepted June 25, 2026 at 9:24 MST

⟐ Answered June 25, 2026 at 8:41 MST

⟐ Commented June 24, 2026 at 17:04 MST

⟐ Answer edited June 24, 2026 at 5:13 MST

⟐ Answered June 22, 2026 at 9:03 MST

*red, white, and blue

⟐ Commented June 20, 2026 at 6:30 MST

When I calibrate or try to dry the clothes it tries to spin the drum and it goes spins like 3 degrees a bit per turn into 3 little movements and then it gives up

What could it be?

Here's a video

It's WW4000, WW11J4473P

⟐ Commented June 20, 2026 at 3:42 MST

The washer just sits still until the cycle stops in drains and spins The water out, fills and sits again u til the end of the rinse cycle then drains and spins. The agitator assembly feels much looser than originally but I can’t see an obvious problem. I really wish I would have kept my 1990s model. I literally replaced everything for 25 years on that washer and have it to my sister when I got the new one which lasted all of 6 years and I replaced it with the one I have. I still have a 1990s refrigerator that still works I’m hesitant to get a new efficient one as everyone seems to be replacing there new ones every 6-8 years.

Please help is you can. Thanks!

⟐ Answer edited June 19, 2026 at 3:10 MST

⟐ Commented June 17, 2026 at 21:04 MST

⟐ Commented June 16, 2026 at 10:31 MST