My 2ds stopped working after leaving on sleep overnight. When I woke up and removed the sleep mode it stayed on but not image or sounds was given. I also could not turn off the 2ds by any means.

I left it on until the battery runned out and fully charged it the next day.

Now it just doesn't turn back on no matter what I do.

⟐ Answered May 03, 2026 at 22:37 MST

⟐ Answered May 03, 2026 at 21:47 MST

⟐ Commented May 03, 2026 at 11:15 MST

⟐ Edited by author May 02, 2026 at 18:12 MST

The result was SMC (1): E006 [SMC_FATAL_CPUGFX] Low priority: VREG_PWRGPAB_CPUGFX_PWRGD missing/timout: Check shorts on V_DRAM1P8, V_SOC1P8, V_SOCPHY. U681, U7, U129, U57 and U480 drive this signal low when a fault is detected.

I checked those test points and got no shorts. I did get shorts on the V_GFXCORE, V_CPUCORE, V_MEMPHY, V_SOC test points though.

I am at a loss as to what could be the issue here. Can anyone guide me in the right direction?

⟐ Commented May 02, 2026 at 15:58 MST

So the problem is that I was given a PS5 controller, but when I turned it on, the X button didn’t work, so I couldn’t log into any account. I opened the controller and did some cleaning I found online, but even after that it still didn’t work. I even removed the rubber piece from the PS button and tried to make contact with the X button membrane, but it still didn’t work.

I know it’s not a problem with the rubber because I used the same PS button rubber and touched the circle button membrane, and on the PS5 the controller registered a back action. That’s why I’m asking, because I don’t know if it’s a circuit issue or something with the pins, and I also don’t know how to fix it. I imagine it would require soldering, and I’m not very good at that and don’t have the right tools.

Whoever can help me, I would really appreciate it.

⟐ Answered May 02, 2026 at 15:54 MST

Translation:

Problems reinstalling system software

How to reinstall PS4 system software

⟐ Answered May 02, 2026 at 15:51 MST

I'm aware that if the blue light flashes on then back off again, it has something to do with ribbon cable issues, which I'm more than aware of. But I have a few concerns: namely, which cable?

The most pressing issue is that the cable connecting the joystick to the main board isn't seated properly. I ordered a few replacements so hopefully the little plastic latch letting the joystick cable seat into the mobo will fix my problems, but I've also tried the bathtub moonshine solution of electrical tape over said cable and it still wouldn't boot: not surprising, it seemed to be misaligned each time I tried it.

One thing worries me though: this little black cable at the top. All the other ribbon cables and connectors appear to be intact, but because this was the first time fully breaking down a N3DSXL, I fear I may have roughed this (particularly delicate) cable up too much and will need to replace it. Can anyone confirm or deny my concerns so I know what to replace if the plastic latch doesn't fix the issue? Every other ribbon cable seems to be in good condition and seated properly.

⟐ Commented May 02, 2026 at 15:43 MST

Thanks in advance!

EDIT (2020.04.22): First off, wow I did not realize people even looked at this thread. Second, I want everyone to know I ended up sending my console to Sony, who kindly repaired it even after the warranty had expired (IIRC I only paid for shipping, it’s been so long IDEK). Thank you to Tronics as well as the many people who I have neglected these past (wow) 4 years for your wonderful tips, and best of luck to those who may have this problem in future. Stay savvy.

⟐ Commented May 02, 2026 at 13:48 MST

⟐ Commented May 02, 2026 at 13:05 MST

⟐ Commented May 02, 2026 at 10:22 MST

⟐ Commented May 02, 2026 at 2:45 MST

⟐ Answered May 02, 2026 at 1:21 MST

⟐ Answered May 02, 2026 at 0:55 MST

I am unable to get into safe mode, or make anything display on screen. I verified that the battery is alright by checking its voltage manually, and it sits at 4.18-4.2 volts.

Thus far, my only troubleshooting has been checking for water damage (none that I could find), and re-seating all the ribbon cables inside, which resulted in no change to the symptoms. It should be noted that this obviously included disconnecting the battery, which was what I originally tried thinking the issue may have been related to the previous firmware issue with Vitas.

Visually, I am unable to find anything wrong aside from some cosmetic scratches. Does anyone have any idea what the issue might be?

⟐ Commented May 01, 2026 at 21:19 MST

⟐ Commented May 01, 2026 at 19:38 MST

⟐ Answered May 01, 2026 at 15:16 MST