GoPro HD Hero 2 Rear Case Replacement

GoPro HD Hero 2 rear case replacement.

http://d3nevzfk7ii3be.cloudfront.net/igi/MoPtGiZKUIUymv31 David Hodson Moderate GoPro HD Hero 2

A rhinoceros ate the rear case of your GoPro? No questions here; you can replace it with a new one.

Tools

Tweezers Phillips #00 Screwdriver Plastic Opening Tools Spudger Installing GoPro HD Hero 2 Back Cover Installing GoPro HD Hero 2 Battery Installing GoPro HD Hero 2 Rear Case Installing GoPro HD Hero 2 SD Board Place your thumb on the indentation in the back case on the side of the GoPro. Place your thumb on the indentation in the back case on the side of the GoPro. Gently press down with your thumb and lift the back cover away from the case to remove it. Gently press down with your thumb and lift the back cover away from the case to remove it. http://d3nevzfk7ii3be.cloudfront.net/igi/cnOABG1BEUhh5KHh http://d3nevzfk7ii3be.cloudfront.net/igi/16HlWyY1dEBCRKgy Slide a plastic opening tool between the battery and the rear case. Slide a plastic opening tool between the battery and the rear case. Gently pry the battery up and out of the rear case. Gently pry the battery up and out of the rear case. http://d3nevzfk7ii3be.cloudfront.net/igi/yHlSqnMECFyNmayS http://d3nevzfk7ii3be.cloudfront.net/igi/xdgn5hdKOOK1SAoL Remove the battery from the case. Remove the battery from the case. http://d3nevzfk7ii3be.cloudfront.net/igi/RZ2wck6UuHEo26V3 Remove the four Phillips #00 screws securing the rear case to the rest of the device: Remove the four Phillips #00 screws securing the rear case to the rest of the device: Two 5.5 mm coarse thread screws. Two 5.5 mm coarse thread screws. Two 4.4 mm fine thread screws. Two 4.4 mm fine thread screws. http://d3nevzfk7ii3be.cloudfront.net/igi/oiHOhCRG4lGHsAPn Slide the edge of a plastic opening tool underneath the sticker on the rear cover and gently peel the sticker up. Slide the edge of a plastic opening tool underneath the sticker on the rear cover and gently peel the sticker up. Once you have enough of the sticker peeled up with the plastic opening tool, grab an edge of it with your fingers and pull it off completely. Once you have enough of the sticker peeled up with the plastic opening tool, grab an edge of it with your fingers and pull it off completely. http://d3nevzfk7ii3be.cloudfront.net/igi/tPP1nfpn1jj4oQAI http://d3nevzfk7ii3be.cloudfront.net/igi/1h6JfYeStXKAjwQX Grasp the rear case and lift it off of the front case. Grasp the rear case and lift it off of the front case. Do not try to completely remove the rear case yet, as it is still attached by the display port ribbon cable. Do not try to completely remove the rear case yet, as it is still attached by the display port ribbon cable. http://d3nevzfk7ii3be.cloudfront.net/igi/JErOqXehntpUMd1f http://d3nevzfk7ii3be.cloudfront.net/igi/N46CPHQKWe53moYG Using a plastic opening tool or your fingernail, flip up the locking tab on the SD board ribbon cable ZIF connector on the motherboard assembly. Using a plastic opening tool or your fingernail, flip up the locking tab on the SD board ribbon cable ZIF connector on the motherboard assembly. Be careful that you are prying on the locking tab, and not the connector itself. Be careful that you are prying on the locking tab, and not the connector itself. Use a pair of tweezers to remove the SD board ribbon cable from its connector on the motherboard. Use a pair of tweezers to remove the SD board ribbon cable from its connector on the motherboard. http://d3nevzfk7ii3be.cloudfront.net/igi/rWvUkWUIoudMxWUk http://d3nevzfk7ii3be.cloudfront.net/igi/IOr6QoLmL622oPht Lift the speaker out of the rear case with the tip of a spudger. Lift the speaker out of the rear case with the tip of a spudger. Remove the rear case. Remove the rear case. http://d3nevzfk7ii3be.cloudfront.net/igi/kteHI4YtZQjLSecH http://d3nevzfk7ii3be.cloudfront.net/igi/ISE1RpAFwbKStO3q http://d3nevzfk7ii3be.cloudfront.net/igi/CJ43TkFHVOjuHrSB Remove the two 5.8 mm Phillips #00 screws securing the SD board cover to the rear case. Remove the two 5.8 mm Phillips #00 screws securing the SD board cover to the rear case. http://d3nevzfk7ii3be.cloudfront.net/igi/l6qvHbllaThS3WeQ Turn the rear case over so that the SD card slot is facing you. Turn the rear case over so that the SD card slot is facing you. Use the tip of a spudger to push the bottom of the SD board cover up and out of the rear case. Use the tip of a spudger to push the bottom of the SD board cover up and out of the rear case. Turn the rear case back over. Turn the rear case back over. Lift the SD board cover out of the rear case with the tip of a spudger and remove it. Lift the SD board cover out of the rear case with the tip of a spudger and remove it. http://d3nevzfk7ii3be.cloudfront.net/igi/PRlQt3SFyTiblNGn http://d3nevzfk7ii3be.cloudfront.net/igi/BBXFAjcpYlILJQ5j http://d3nevzfk7ii3be.cloudfront.net/igi/2OyxXIKy1JTQOPoE Grasp the SD board ribbon cable gently and pull the SD board out of the rear case. Grasp the SD board ribbon cable gently and pull the SD board out of the rear case. http://d3nevzfk7ii3be.cloudfront.net/igi/vMVfNvPACoNaRJMh http://d3nevzfk7ii3be.cloudfront.net/igi/MI11Oj4sBODURSVD The rear case remains. The rear case remains. http://d3nevzfk7ii3be.cloudfront.net/igi/Y1nkYMlpmKVOty63

To reassemble your device, follow these instructions in reverse order.