Motorola C139 Phone Teardown This will show a complete Teardown of the Motorola C139 Phone. http://d3nevzfk7ii3be.cloudfront.net/igi/p6B63hlijKLoJspS Kyle Olbrich 15 to 20 minutes Moderate Motorola C139
Tools
 Plastic Opening Tools T5 Torx Screwdriver An awesome member of our community made this guide. It is not managed by iFixit staff. This guide is being worked on by hardworking students. Installing Motorola C139 Phone Battery Installing Motorola C139 Phone SIM Card Installing Motorola C139 Phone Rear Casing Installing Motorola C139 Phone Keypad & Faceplate Installing Motorola C139 Phone Antenna Installing Motorola C139 Phone Vibration Mechanism Installing Motorola C139 Phone Speaker Begin by flipping your phone over so that the back cover is facing up. Begin by flipping your phone over so that the back cover is facing up. Apply force to the back cover and simultaneously slide the cover down. Apply force to the back cover and simultaneously slide the cover down. Note: Applying pressure on the ridges will make it easier to remove the cover. Note: Applying pressure on the ridges will make it easier to remove the cover. http://d3nevzfk7ii3be.cloudfront.net/igi/PbLiLOUqmLkXiEsg http://d3nevzfk7ii3be.cloudfront.net/igi/BSKli2yourPZ6CiD http://d3nevzfk7ii3be.cloudfront.net/igi/LE15OZKVkxtWjPPo Press the button labeled "PUSH" located at the bottom back of the phone. This will release the battery. Press the button labeled "PUSH" located at the bottom back of the phone. This will release the battery. Lift and remove the battery. Lift and remove the battery. http://d3nevzfk7ii3be.cloudfront.net/igi/U3VEYmtAtY5GTCa6 http://d3nevzfk7ii3be.cloudfront.net/igi/XssDmJCVDyDpiVDS http://d3nevzfk7ii3be.cloudfront.net/igi/ekSWaUHmYKWjAccX Do not bend or scratch the SIM card. In addition, keep it away from static electricity, dust, and water. Do not bend or scratch the SIM card. In addition, keep it away from static electricity, dust, and water. Gently slide the SIM card out and lift to remove it from the phone. Gently slide the SIM card out and lift to remove it from the phone. http://d3nevzfk7ii3be.cloudfront.net/igi/sHuHbIlNIwUhTpOB http://d3nevzfk7ii3be.cloudfront.net/igi/lVMXphKvhROwHKaP http://d3nevzfk7ii3be.cloudfront.net/igi/bPVauDPfe2YUQC5c Use a Torx T-5 screwdriver to remove the screws on the back of the phone. Use a Torx T-5 screwdriver to remove the screws on the back of the phone. The screws are 6.86 mm long and 1.61mm in diameter. The screws are 6.86 mm long and 1.61mm in diameter. http://d3nevzfk7ii3be.cloudfront.net/igi/dlLyk4It4LZdxP2S http://d3nevzfk7ii3be.cloudfront.net/igi/DFf5R2hq6p1nNGeZ http://d3nevzfk7ii3be.cloudfront.net/igi/6CXwCZr5Ki3bMC6k Slide a pry tool underneath the adhesive rubber stip and peel it back away from the phone. Slide a pry tool underneath the adhesive rubber stip and peel it back away from the phone. Repeat for the other side Repeat for the other side http://d3nevzfk7ii3be.cloudfront.net/igi/Un1KlODsiWVdCmjj http://d3nevzfk7ii3be.cloudfront.net/igi/AKYqnbwJuUJCGSYc http://d3nevzfk7ii3be.cloudfront.net/igi/mv26AkUwKEBrDgpW Insert the pry tool in the slit on the side of the phone and slide it down until you hear an audible click and the phone bottom loosens from the top. Insert the pry tool in the slit on the side of the phone and slide it down until you hear an audible click and the phone bottom loosens from the top. Use the pry tool to release the two hooks on each side and the two hooks at the top holding the case together. Use the pry tool to release the two hooks on each side and the two hooks at the top holding the case together. Release a total of six hooks from the sides and top to free the phone into two halves. Release a total of six hooks from the sides and top to free the phone into two halves. http://d3nevzfk7ii3be.cloudfront.net/igi/2DyHHOFOA54Cev1c http://d3nevzfk7ii3be.cloudfront.net/igi/nvMkcXYwAHutuIy1 http://d3nevzfk7ii3be.cloudfront.net/igi/exTlvsIPVC4NxNgB Using a Torx T-5 screwdriver remove the screws at the top of the phone. Using a Torx T-5 screwdriver remove the screws at the top of the phone. The screws are 6.86 mm long and 1.61mm in diameter. The screws are 6.86 mm long and 1.61mm in diameter. http://d3nevzfk7ii3be.cloudfront.net/igi/DyfICCaYLuPaGPpY http://d3nevzfk7ii3be.cloudfront.net/igi/t4MwvPvnMQpoNMHQ http://d3nevzfk7ii3be.cloudfront.net/igi/ZMMG3QsGPpuRlKZx Use plastic pry tools to free the circuit board from the case Use plastic pry tools to free the circuit board from the case There are two hooks (one on each side) holding the circuit board into the case. There are two hooks (one on each side) holding the circuit board into the case. Then grip the circuit board and lift to remove the circuit board from the case Then grip the circuit board and lift to remove the circuit board from the case http://d3nevzfk7ii3be.cloudfront.net/igi/uLOlVMhRlXyBIWJ1 http://d3nevzfk7ii3be.cloudfront.net/igi/sSK2MSAFZglRwAOa http://d3nevzfk7ii3be.cloudfront.net/igi/ABJtXSIGYDkgbPWr On the top half of the phone push downwards on the number keys to free the keypad from the top of the phone. On the top half of the phone push downwards on the number keys to free the keypad from the top of the phone. http://d3nevzfk7ii3be.cloudfront.net/igi/pixyPtVSwg32iHoM http://d3nevzfk7ii3be.cloudfront.net/igi/U1wTPLZbG3IAkeaG Unhook the antenna by releasing the two hooks, one on each side of the phone. Unhook the antenna by releasing the two hooks, one on each side of the phone. Detach the antenna from the back of the circuit board Detach the antenna from the back of the circuit board This small black rubber cover may detach. This small black rubber cover may detach. http://d3nevzfk7ii3be.cloudfront.net/igi/2yvbugICbDMXH6oB http://d3nevzfk7ii3be.cloudfront.net/igi/CHUui5XBHDJayZoc http://d3nevzfk7ii3be.cloudfront.net/igi/4uEmYHoBkndsrfU1 Using your hands or the pry tool, gently lift the vibration mechanism out of the rear casing. Using your hands or the pry tool, gently lift the vibration mechanism out of the rear casing. http://d3nevzfk7ii3be.cloudfront.net/igi/iAIhQjJ3jCSUCFvo http://d3nevzfk7ii3be.cloudfront.net/igi/ZKaILlqsXgRHyLHa Unhook the 10 clips holding the metal screen cover in place and pull up to detach it from the logic board. Unhook the 10 clips holding the metal screen cover in place and pull up to detach it from the logic board. There are four clips at the top, two along each side, and two clips at the bottom of the metal cover. There are four clips at the top, two along each side, and two clips at the bottom of the metal cover. http://d3nevzfk7ii3be.cloudfront.net/igi/ANrVECMfKWjbZIf4 http://d3nevzfk7ii3be.cloudfront.net/igi/Mlxtwmxq6LNnMZJD http://d3nevzfk7ii3be.cloudfront.net/igi/QhAPKoPxAaptDcqa Lift to remove the speaker from its contact point on the logic board. Lift to remove the speaker from its contact point on the logic board. http://d3nevzfk7ii3be.cloudfront.net/igi/HlkM5ypWTAn4wdhM http://d3nevzfk7ii3be.cloudfront.net/igi/xKoCLbtqRFpB2BGm List of Parts: Battery, SIM Card, Vibration mechanism, back cover, Front Case, Back Case, 2x rubber sides, 4x Screws, Antenna, Speaker, Keypad, Metal screen cover. List of Parts: Battery, SIM Card, Vibration mechanism, back cover, Front Case, Back Case, 2x rubber sides, 4x Screws, Antenna, Speaker, Keypad, Metal screen cover. http://d3nevzfk7ii3be.cloudfront.net/igi/p6B63hlijKLoJspS

To reassemble your device, follow these instructions in reverse order.