Installing MacBook Air Models A1237 and A1304 Fan
http://d3nevzfk7ii3be.cloudfront.net/igi/a1IAefBSJjMuJDUA
Walter Galan
Moderate
MacBook Air Models A1237 and A1304
Replacing a defective fan is pretty easy and will keep your laptop running cool.
Replacing a defective fan is pretty easy and will keep your laptop running cool.
Arctic Silver ArctiClean
Arctic Silver Thermal Paste
Phillips 00 Screwdriver
Spudger
MacBook Air (Original) Fan
Installing MacBook Air Models A1237 and A1304 Lower Case
Installing MacBook Air Models A1237 and A1304 Battery
Installing MacBook Air Models A1237 and A1304 Hard Drive
Installing MacBook Air Models A1237 and A1304 Heat Sink
Remove the following 10 screws securing the lower case to the Air:
Remove the following 10 screws securing the lower case to the Air:
Six 2.8 mm Phillips screws.
Six 2.8 mm Phillips screws.
Two 3.8 mm Phillips screws.
Two 3.8 mm Phillips screws.
Two 5.4 mm Phillips screws.
Two 5.4 mm Phillips screws.
http://d3nevzfk7ii3be.cloudfront.net/igi/YdQ32CY4ZKfWaZbD
Slightly lift the lower case near the vents and push it toward the rear of the computer to free the mounting tabs.
Slightly lift the lower case near the vents and push it toward the rear of the computer to free the mounting tabs.
http://d3nevzfk7ii3be.cloudfront.net/igi/6LJgw4foS4BqQcZ4
http://d3nevzfk7ii3be.cloudfront.net/igi/qEWO2PIUpaRF4ZMG
Disconnect the battery connector by pulling it straight out of its socket.
Disconnect the battery connector by pulling it straight out of its socket.
http://d3nevzfk7ii3be.cloudfront.net/igi/VNYlBOXhmBhhRH2n
Remove the following nine screws securing the battery to the Air:
Remove the following nine screws securing the battery to the Air:
Four 2.9 mm Phillips.
Four 2.9 mm Phillips.
Four 3.8 mm Phillips.
Four 3.8 mm Phillips.
One 7.2 mm Phillips.
One 7.2 mm Phillips.
http://d3nevzfk7ii3be.cloudfront.net/igi/AXEt6ulWWPPhnkd4
Lift the battery out of the Air.
Lift the battery out of the Air.
http://d3nevzfk7ii3be.cloudfront.net/igi/oTSXZsxJhtSHYHDZ
Disconnect the port hatch ribbon cable from the logic board by pulling it straight up by its black pull tab.
Disconnect the port hatch ribbon cable from the logic board by pulling it straight up by its black pull tab.
Pull the audio out ribbon cable off the adhesive securing it to the upper case.
Pull the audio out ribbon cable off the adhesive securing it to the upper case.
Use a spudger to pry the audio out ribbon cable connector board off the hard drive bracket.
Use a spudger to pry the audio out ribbon cable connector board off the hard drive bracket.
http://d3nevzfk7ii3be.cloudfront.net/igi/tEDvxLoAOkWLcUW4
http://d3nevzfk7ii3be.cloudfront.net/igi/aGWH62rPoJV2CHgr
http://d3nevzfk7ii3be.cloudfront.net/igi/vkr1D1tXGORV4pJc
Disconnect the audio out cable from its socket on the port hatch ribbon cable.
Disconnect the audio out cable from its socket on the port hatch ribbon cable.
http://d3nevzfk7ii3be.cloudfront.net/igi/FaQxPdBMW4FvKZ6g
Use a spudger to pry the hard drive cable connector up off the logic board.
Use a spudger to pry the hard drive cable connector up off the logic board.
http://d3nevzfk7ii3be.cloudfront.net/igi/fdYFJHZCNFBNPoke
Use the sharp end of a spudger to de-route the microphone cable from the hard drive bracket.
Use the sharp end of a spudger to de-route the microphone cable from the hard drive bracket.
Remove the cosmetic screw cover from the adhesive securing it to the hard drive bracket.
Remove the cosmetic screw cover from the adhesive securing it to the hard drive bracket.
http://d3nevzfk7ii3be.cloudfront.net/igi/dHilYruXLwxGNxhQ
http://d3nevzfk7ii3be.cloudfront.net/igi/YYNJZaEUb6jTMknW
Remove the four Phillips screws securing the hard drive assembly to the upper case.
Remove the four Phillips screws securing the hard drive assembly to the upper case.
http://d3nevzfk7ii3be.cloudfront.net/igi/GDb2BFN5NgGyqKqH
Lift the hard drive assembly out of the upper case.
Lift the hard drive assembly out of the upper case.
http://d3nevzfk7ii3be.cloudfront.net/igi/AZunO3LXTkBgQlXF
Use the tip of a spudger to pull the fan cable connector straight away from its connector on the logic board.
Use the tip of a spudger to pull the fan cable connector straight away from its connector on the logic board.
http://d3nevzfk7ii3be.cloudfront.net/igi/HqIlqSAZQLZo1qCo
Use the tip of a spudger to move the cosmetic fan cover aside.
Use the tip of a spudger to move the cosmetic fan cover aside.
http://d3nevzfk7ii3be.cloudfront.net/igi/PIXEM12MAMHnPoNi
http://d3nevzfk7ii3be.cloudfront.net/igi/IEtebJJTcuQxieJI
If you have the original version of the MacBook Air (A1237), refer to picture 1. Remove the following screws securing the heat sink to the logic board:
If you have the original version of the MacBook Air (A1237), refer to picture 1. Remove the following screws securing the heat sink to the logic board:
One 5.9 mm Phillips screw.
One 5.9 mm Phillips screw.
Two 1.9 mm Phillips screws.
Two 1.9 mm Phillips screws.
One 1.9 mm Phillips screw.
One 1.9 mm Phillips screw.
If you have the A1304 version of MacBook Air, refer to picture 2. Remove the following screws securing the heat sink to the logic board:
If you have the A1304 version of MacBook Air, refer to picture 2. Remove the following screws securing the heat sink to the logic board:
One 5.0 mm Phillips screw
One 5.0 mm Phillips screw
Five 1.9 mm Philips screws.
Five 1.9 mm Philips screws.
One 2.5 mm Phillips screw.
One 2.5 mm Phillips screw.
http://d3nevzfk7ii3be.cloudfront.net/igi/4RMjwVdT5xkiR5EL
http://d3nevzfk7ii3be.cloudfront.net/igi/dyVYKtjuJaKyYDpk
Lift the processor clamp off the heat sink.
Lift the processor clamp off the heat sink.
http://d3nevzfk7ii3be.cloudfront.net/igi/GkgQJnLBFEeBBsrD
Deroute the microphone cable away from the channel in the fan.
Deroute the microphone cable away from the channel in the fan.
http://d3nevzfk7ii3be.cloudfront.net/igi/hLAqkMTZQRnhKqkB
Lift the heat sink up off the logic board.
Lift the heat sink up off the logic board.
Be mindful of the microphone cable when lifting the heat sink, as it can get tangled on the top edge of the fan.
Be mindful of the microphone cable when lifting the heat sink, as it can get tangled on the top edge of the fan.
When you mount the heat sink back onto the logic board, be sure to apply a new layer of thermal paste. We have a <a href="/Guide/Applying+Thermal+Paste/744/1">guide</a> that makes replacing the thermal paste easy.
When you mount the heat sink back onto the logic board, be sure to apply a new layer of thermal paste. We have a [guide|744|guide] that makes replacing the thermal paste easy.
http://d3nevzfk7ii3be.cloudfront.net/igi/X6REqZyPyUAn4P1v
If you have the A1304 version of MacBook Air, the fan is a separate component. The following steps therefore do not apply to your model. Simply detach the microphone cable from where it is adhered to the fan, and lift the fan out from the machine at this point.
If you have the A1304 version of MacBook Air, the fan is a separate component. The following steps therefore do not apply to your model. Simply detach the microphone cable from where it is adhered to the fan, and lift the fan out from the machine at this point.
Remove the four 2.5 mm Phillips screws securing the fan to the heat sink assembly.
Remove the four 2.5 mm Phillips screws securing the fan to the heat sink assembly.
http://d3nevzfk7ii3be.cloudfront.net/igi/RWaloP6ePnHQXRbx
Lift the heat sink assembly up off the fan.
Lift the heat sink assembly up off the fan.
http://d3nevzfk7ii3be.cloudfront.net/igi/xgtD2Jb4TdDwJEPx
Lift the cosmetic fan bracket out of the fan.
Lift the cosmetic fan bracket out of the fan.
Fan remains.
Fan remains.
http://d3nevzfk7ii3be.cloudfront.net/igi/iEPBOuPFjiqOFDnS
To reassemble your device, follow these instructions in reverse order.