Installing HTC Hero 200 Motherboard This guide will illustrate the appropriate steps necessary to remove a damaged mother board and replace it with a functioning unit. http://d3nevzfk7ii3be.cloudfront.net/igi/LyP51LZl1hLxwBZi Rosalind Villalvazo Moderate HTC Hero 200
Tools
 Plastic Opening Tools Small Flathead Screwdriver T6 Torx Screwdriver Better photos will improve this guide. Help out by taking, editing, or uploading new ones! An awesome member of our community made this guide. It is not managed by iFixit staff. Installing HTC Hero 200 Back Case Remove battery cover by pushing firmly with your palm up towards the camera. Remove battery cover by pushing firmly with your palm up towards the camera. Remove the battery and SD card. Remove the battery and SD card. Locate and remove the four Torx screws highlighted here, with the phone laying face down on your work space. Locate and remove the four Torx screws highlighted here, with the phone laying face down on your work space. http://d3nevzfk7ii3be.cloudfront.net/igi/VfBhKcVa1EAmcWpC Pry the inside back cover from the device using a plastic opening tool or small flathead screwdriver. Pry the inside back cover from the device using a plastic opening tool or small flathead screwdriver. <strong>Carefully insert</strong> the flat end between the back and front enclosure, working your way around the rim. '''Carefully insert''' the flat end between the back and front enclosure, working your way around the rim. http://d3nevzfk7ii3be.cloudfront.net/igi/yjSfwlcbGGT2lhQy <strong>Gently depress and release</strong> the small plastic tabs around the rim in the front enclosure, highlighted here. '''Gently depress and release''' the small plastic tabs around the rim in the front enclosure, highlighted here. It is best to start with the tab found on the top center of the phone, as it is easiest to locate. It is best to start with the tab found on the top center of the phone, as it is easiest to locate. http://d3nevzfk7ii3be.cloudfront.net/igi/4UdEVI4X3HdorqPs <strong>Carefully separate</strong> the front and back enclosures once all of the clips have been disengaged. '''Carefully separate''' the front and back enclosures once all of the clips have been disengaged. Be sure to not separate too quickly or you risk breaking an attached tab. Be sure to not separate too quickly or you risk breaking an attached tab. http://d3nevzfk7ii3be.cloudfront.net/igi/qM1b3GyZ5DI43RSG http://d3nevzfk7ii3be.cloudfront.net/igi/enP2cNawgkHmgDak Release the two ribbon cables using a plastic opening tool. Release the two ribbon cables using a plastic opening tool. <strong>Gently pry up</strong> the pop connectors used to attach the ribbon cables to the motherboard. '''Gently pry up''' the pop connectors used to attach the ribbon cables to the motherboard. http://d3nevzfk7ii3be.cloudfront.net/igi/DdEZcieTRtW2DsIV http://d3nevzfk7ii3be.cloudfront.net/igi/Dn2hErFXGvBkDFcb Remove the two screws located at the bottom left and right of the motherboard using a small Phillips screwdriver. Remove the two screws located at the bottom left and right of the motherboard using a small Phillips screwdriver. http://d3nevzfk7ii3be.cloudfront.net/igi/ZTDxJwBmWfyuB2F3 http://d3nevzfk7ii3be.cloudfront.net/igi/Fc5CAamXKIRQgnOo <strong>Gently lift</strong> the motherboard out of the front enclosure once the screws are removed. '''Gently lift''' the motherboard out of the front enclosure once the screws are removed. http://d3nevzfk7ii3be.cloudfront.net/igi/uUJ2oBLlQTPETscN http://d3nevzfk7ii3be.cloudfront.net/igi/qLXWUyyfgPj4pcQv

To reassemble your device, follow these instructions in reverse order.