Installing PowerBook G4 Aluminum 15" 1.5-1.67 GHz Right Clutch Hinge
Replace the right clutch hinge on the display of your 1.5-1.67 GHz 15" Aluminum PowerBook G4.
http://d3nevzfk7ii3be.cloudfront.net/igi/UuWgGqxewerlrW5L
Walter Galan
Very difficult
PowerBook G4 Aluminum 15" 1.5-1.67 GHz
Replace a clutch hinge to keep your display opening smoothly.
Replace a clutch hinge to keep your display opening smoothly.
4mm Nut Driver
Anti-Static Wrist Strap
Arctic Silver ArctiClean
Arctic Silver Thermal Paste
Coin
iPod Opening Tools
Phillips 00 Screwdriver
Push Pin
Spudger
T6 Torx Screwdriver
T8 Torx Screwdriver
G4 Aluminum 15" Right Clutch Hinge
Installing PowerBook G4 Aluminum 15" 1.5-1.67 GHz Battery
Installing PowerBook G4 Aluminum 15" 1.5-1.67 GHz Upper Case
Installing PowerBook G4 Aluminum 15" 1.5-1.67 GHz Right Ambient Light Sensor
Installing PowerBook G4 Aluminum 15" 1.5-1.67 GHz Logic Board
Installing PowerBook G4 Aluminum 15" 1.5-1.67 GHz Speakers
Installing PowerBook G4 Aluminum 15" 1.5-1.67 GHz PC Card Cage
Installing PowerBook G4 Aluminum 15" 1.5-1.67 GHz Display
Installing PowerBook G4 Aluminum 15" 1-1.5 GHz Rear Display Bezel
Installing PowerBook G4 Aluminum 15" 1-1.5 GHz Clutch Cover
Use a coin to turn the battery locking screw 90 degrees clockwise.
Use a coin to turn the battery locking screw 90 degrees clockwise.
Lift the battery out of the computer.
Lift the battery out of the computer.
http://d3nevzfk7ii3be.cloudfront.net/igi/TvBQUggXavMmpVpg
Remove the four Phillips screws from the memory door.
Remove the four Phillips screws from the memory door.
Slide the memory door away from the memory compartment.
Slide the memory door away from the memory compartment.
http://d3nevzfk7ii3be.cloudfront.net/igi/JfbhaRZjZwkQBgnF
Remove the following 8 screws:
Remove the following 8 screws:
Two 3 mm Phillips in the battery compartment, on either side of the battery contacts.
Two 3 mm Phillips in the battery compartment, on either side of the battery contacts.
Two 12 mm Phillips on either side of the memory compartment.
Two 12 mm Phillips on either side of the memory compartment.
Four 16 mm Phillips along the hinge.
Four 16 mm Phillips along the hinge.
http://d3nevzfk7ii3be.cloudfront.net/igi/xFJTEolCJHOSmJfk
Rotate the computer 90 degrees clockwise, so that the power receptacle faces you.
Rotate the computer 90 degrees clockwise, so that the power receptacle faces you.
Remove the three 3 mm Phillips screws.
Remove the three 3 mm Phillips screws.
When replacing these screws, you must place each screw in the correct order. Begin by installing the screw closest to the display hinge, and go out from there.
When replacing these screws, you must place each screw in the correct order. Begin by installing the screw closest to the display hinge, and go out from there.
http://d3nevzfk7ii3be.cloudfront.net/igi/QbUxYBl2KaXGpxwM
Turn the computer 90 degrees clockwise so that the hinge faces you.
Turn the computer 90 degrees clockwise so that the hinge faces you.
Remove the bottom 5 mm Phillips screw on either side of the hinge (two total).
Remove the bottom 5 mm Phillips screw on either side of the hinge (two total).
http://d3nevzfk7ii3be.cloudfront.net/igi/tUJFONe6DUHDHEvN
Rotate the computer 90 degrees clockwise, so that the ports face you.
Rotate the computer 90 degrees clockwise, so that the ports face you.
Remove the three 3 mm Phillips screws.
Remove the three 3 mm Phillips screws.
When replacing these screws, you must place each screw in the correct order. Begin by installing the screw closest to the display hinge, and go out from there.
When replacing these screws, you must place each screw in the correct order. Begin by installing the screw closest to the display hinge, and go out from there.
http://d3nevzfk7ii3be.cloudfront.net/igi/XmCrMBBxNVqlrYAg
Turn the computer over and open the display.
Turn the computer over and open the display.
Remove the two 1.5 mm hex screws in either corner, next to the display (a T6 Torx driver will work, but repeated use will strip the screws).
Remove the two 1.5 mm hex screws in either corner, next to the display (a T6 Torx driver will work, but repeated use will strip the screws).
http://d3nevzfk7ii3be.cloudfront.net/igi/KEtZoBso1ljEJlv4
Grasp the back corners of the upper case and pull up. Do not pull the upper case off yet; you still need to disconnect the keyboard and trackpad cable.
Grasp the back corners of the upper case and pull up. Do not pull the upper case off yet; you still need to disconnect the keyboard and trackpad cable.
Lift the back of the case up and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case.
Lift the back of the case up and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case.
http://d3nevzfk7ii3be.cloudfront.net/igi/gIl2YaeIqSQJuWn5
Rotate the upper case up and toward the screen, so that the upper case rests against it.
Rotate the upper case up and toward the screen, so that the upper case rests against it.
http://d3nevzfk7ii3be.cloudfront.net/igi/I2Q1V664KFX5nTpO
Remove the orange tape securing the trackpad ribbon to the logic board.
Remove the orange tape securing the trackpad ribbon to the logic board.
Disconnect the trackpad ribbon from the logic board.
Disconnect the trackpad ribbon from the logic board.
Remove the upper case from the computer.
Remove the upper case from the computer.
http://d3nevzfk7ii3be.cloudfront.net/igi/ZN1oFmZLYi4VsAC6
Remove the 9.5 mm silver Phillips screw from the top of the right ambient light sensor board.
Remove the 9.5 mm silver Phillips screw from the top of the right ambient light sensor board.
Remove the small 3 mm black Phillips screw from the bottom of the board.
Remove the small 3 mm black Phillips screw from the bottom of the board.
http://d3nevzfk7ii3be.cloudfront.net/igi/Se2LKCTuxFPcjkFj
Lift the right ambient light sensor board from the computer.
Lift the right ambient light sensor board from the computer.
http://d3nevzfk7ii3be.cloudfront.net/igi/J4GBIWLDFuwJfGvw
Remove the two black Phillips screws from the right speaker.
Remove the two black Phillips screws from the right speaker.
Lift the speaker away from the logic board and place it aside
Lift the speaker away from the logic board and place it aside
http://d3nevzfk7ii3be.cloudfront.net/igi/nv1yhP6vCXGKnWAv
Use your fingernail to flip up the black plastic flap locking the modem cable in place.
Use your fingernail to flip up the black plastic flap locking the modem cable in place.
Slide the modem cable from its connector.
Slide the modem cable from its connector.
http://d3nevzfk7ii3be.cloudfront.net/igi/5fqjCfNPc2YUHBIt
Disconnect the 13 indicated cables, removing tape as necessary.
Disconnect the 13 indicated cables, removing tape as necessary.
When re-installing the board, make sure the two small connectors at the right hand side are above the board before inserting the screws.
When re-installing the board, make sure the two small connectors at the right hand side are above the board before inserting the screws.
http://d3nevzfk7ii3be.cloudfront.net/igi/rVhohAZpNwRRJBod
Remove the following 8 Phillips screws from the logic board:
Remove the following 8 Phillips screws from the logic board:
Three 6.5 mm in the upper left corner.
Three 6.5 mm in the upper left corner.
Five 4.5 mm around the edges.
Five 4.5 mm around the edges.
http://d3nevzfk7ii3be.cloudfront.net/igi/SmQQaB4mdNLelIlT
Two cables still connect to the logic board and must be removed before pulling the board entirely out of the computer.
Two cables still connect to the logic board and must be removed before pulling the board entirely out of the computer.
Use a spudger to gently (very gently) pry up the left side of the logic board.
Use a spudger to gently (very gently) pry up the left side of the logic board.
If the logic board does not immediately come free, it may be necessary to soften the thermal paste between the logic board and heat sink. You can soften the thermal compound using a hairdryer. Move the hairdryer back and forth between the two fans about one inch above the logic board for one minute. At this point, the logic board should now come free easily.
If the logic board does not immediately come free, it may be necessary to soften the thermal paste between the logic board and heat sink. You can soften the thermal compound using a hairdryer. Move the hairdryer back and forth between the two fans about one inch above the logic board for one minute. At this point, the logic board should now come free easily.
http://d3nevzfk7ii3be.cloudfront.net/igi/Nec2Pb2DNVFYwuce
Disconnect the DC-In connector from the left side of the logic board.
Disconnect the DC-In connector from the left side of the logic board.
http://d3nevzfk7ii3be.cloudfront.net/igi/RCqVQ2TdjklDZKGd
Disconnect the battery cable from the front, left corner of the logic board.
Disconnect the battery cable from the front, left corner of the logic board.
http://d3nevzfk7ii3be.cloudfront.net/igi/owe5lZbhVjJEPpkJ
Grasp the logic board at the left edge with one hand and at the thinnest section with the other hand. Lift the left edge of the board up to approximately a 30 degree angle (if you don't have your protractor handy, just lift until the DVI port clears the right hinge).
Grasp the logic board at the left edge with one hand and at the thinnest section with the other hand. Lift the left edge of the board up to approximately a 30 degree angle (if you don't have your protractor handy, just lift until the DVI port clears the right hinge).
Once the logic board clears the ports, slide it out to the left.
Once the logic board clears the ports, slide it out to the left.
http://d3nevzfk7ii3be.cloudfront.net/igi/KUBrtI5HhnD4XTH1
Important: when you reinstall a logic board, you'll need to replace the thermal paste that goes between the processor on the logic board and the heat sink. Failure to remove the old paste and apply a new layer can cause the computer to overheat and sustain damage.
Important: when you reinstall a logic board, you'll need to replace the thermal paste that goes between the processor on the logic board and the heat sink. Failure to remove the old paste and apply a new layer can cause the computer to overheat and sustain damage.
To properly reassemble your PowerBook, you'll have to clean off and replace the old thermal compound. Use our <a href="/Guide/Applying+Thermal+Paste/744/1">Applying Thermal Paste Guide</a> to prepare the processor and heat sink surfaces.
To properly reassemble your PowerBook, you'll have to clean off and replace the old thermal compound. Use our [guide|744|Applying Thermal Paste Guide] to prepare the processor and heat sink surfaces.
http://d3nevzfk7ii3be.cloudfront.net/igi/HZZPQh1Y3TMSkxwQ
Use a firm plastic edge to scrape the thermal material off the processor.
Use a firm plastic edge to scrape the thermal material off the processor.
When replacing the logic board, make sure all cables are routed around and above - not under - it, and to connect the two cables that do go beneath before pushing the board into place.
When replacing the logic board, make sure all cables are routed around and above - not under - it, and to connect the two cables that do go beneath before pushing the board into place.
Place the logic board back in the computer, trying not to move it around once the processor has come into contact with the newly-applied thermal paste.
Place the logic board back in the computer, trying not to move it around once the processor has come into contact with the newly-applied thermal paste.
http://d3nevzfk7ii3be.cloudfront.net/igi/LYMPlBqn26fWZ1ty
Remove the two 3 mm black Phillips screws from the left ambient light sensor board.
Remove the two 3 mm black Phillips screws from the left ambient light sensor board.
Lift the left ambient light sensor board out of the computer, removing tape as necessary.
Lift the left ambient light sensor board out of the computer, removing tape as necessary.
http://d3nevzfk7ii3be.cloudfront.net/igi/qFHNn1wafoOXoxqU
Deroute the Bluetooth and RJ-11 cables from around the left side of the speaker.
Deroute the Bluetooth and RJ-11 cables from around the left side of the speaker.
http://d3nevzfk7ii3be.cloudfront.net/igi/qdvXhoVsr4nr5Lid
Disconnect the speaker cable from the DC/Sound card.
Disconnect the speaker cable from the DC/Sound card.
http://d3nevzfk7ii3be.cloudfront.net/igi/YYbSVnRsv6Bj6O2o
Remove the 4 mm hex nut from below the left speaker.
Remove the 4 mm hex nut from below the left speaker.
Remove the 3 mm black Phillips screw from bottom left corner of the speaker assembly, to the left of the battery compartment.
Remove the 3 mm black Phillips screw from bottom left corner of the speaker assembly, to the left of the battery compartment.
http://d3nevzfk7ii3be.cloudfront.net/igi/sCbMDQrcvyBpbMNQ
Lift the speaker assembly (including the right speaker) out of the computer.
Lift the speaker assembly (including the right speaker) out of the computer.
http://d3nevzfk7ii3be.cloudfront.net/igi/LQDfGgUMcVOnvQPG
Remove the two 4.2 mm silver Phillips screws from the left corners of the PC card cage.
Remove the two 4.2 mm silver Phillips screws from the left corners of the PC card cage.
Next the two 6.8 mm shouldered screws go on the right side of the card cage.
Next the two 6.8 mm shouldered screws go on the right side of the card cage.
http://d3nevzfk7ii3be.cloudfront.net/igi/RT5VxxQMFgS4iKQI
Lift the PC card cage up and remove it from the computer.
Lift the PC card cage up and remove it from the computer.
When replacing the PC card cage, make sure you attach it to the post on the metal eject button.
When replacing the PC card cage, make sure you attach it to the post on the metal eject button.
http://d3nevzfk7ii3be.cloudfront.net/igi/MUSukcvJLaBArRP4
Remove the two 4.2 mm silver Phillips screws from either side of the large orange Airport ribbon.
Remove the two 4.2 mm silver Phillips screws from either side of the large orange Airport ribbon.
http://d3nevzfk7ii3be.cloudfront.net/igi/OyGWYk2IEmO13Ik1
Lift the Airport card out of the computer and slide a spudger between the card and the antenna connector to disconnect the cable from the card.
Lift the Airport card out of the computer and slide a spudger between the card and the antenna connector to disconnect the cable from the card.
Deroute the antenna cable from the side of the card, removing tape as necessary.
Deroute the antenna cable from the side of the card, removing tape as necessary.
You don't need to remove the Airport card entirely. We're just trying to free up the Airport antenna cable.
You don't need to remove the Airport card entirely. We're just trying to free up the Airport antenna cable.
http://d3nevzfk7ii3be.cloudfront.net/igi/OOUJFI1sCwuPN6W4
Using a spudger, pry up the Bluetooth board from the cavity in front of the battery compartment.
Using a spudger, pry up the Bluetooth board from the cavity in front of the battery compartment.
http://d3nevzfk7ii3be.cloudfront.net/igi/civjiRFSC3kZPUy2
Disconnect the Bluetooth antenna cable from the Bluetooth board.
Disconnect the Bluetooth antenna cable from the Bluetooth board.
http://d3nevzfk7ii3be.cloudfront.net/igi/EPhqDTEXryHKUqUs
Close the display and turn the hinge side of the computer to face you.
Close the display and turn the hinge side of the computer to face you.
Remove the remaining Phillips screw on either side of the hinge (two screws total).
Remove the remaining Phillips screw on either side of the hinge (two screws total).
http://d3nevzfk7ii3be.cloudfront.net/igi/gNdhgtN3ooESoBj3
Open the display and turn the computer so the screen faces you.
Open the display and turn the computer so the screen faces you.
Remove the 10 mm T8 Torx screw closer to the display on either side of the hinge (two screws total).
Remove the 10 mm T8 Torx screw closer to the display on either side of the hinge (two screws total).
When replacing the display, make sure that the right screw pins down the ground loop from the display data cable.
When replacing the display, make sure that the right screw pins down the ground loop from the display data cable.
http://d3nevzfk7ii3be.cloudfront.net/igi/ioMWmfrpJRUfOATI
Be sure to support the display with one hand while removing the final two screws.
Be sure to support the display with one hand while removing the final two screws.
Remove the longer 13 mm shouldered T8 Torx screw remaining on either hinge (two screws total).
Remove the longer 13 mm shouldered T8 Torx screw remaining on either hinge (two screws total).
http://d3nevzfk7ii3be.cloudfront.net/igi/mrUKwpkTyarQZEqi
Lift the display off.
Lift the display off.
http://d3nevzfk7ii3be.cloudfront.net/igi/ROhLYWPKYmPl1sSf
Remove the two 11 mm X 1.5 mm hex screws near the lower left and right corners of the display.
Remove the two 11 mm X 1.5 mm hex screws near the lower left and right corners of the display.
A T6 Torx screwdriver works just fine.
A T6 Torx screwdriver works just fine.
http://d3nevzfk7ii3be.cloudfront.net/igi/NvSJSFYUXhUtXj1V
http://d3nevzfk7ii3be.cloudfront.net/igi/Og2rP3BNi6mn32Qo
Insert the flat end of a spudger between the front display bezel and the plastic rim attached to the rear bezel near the lower left corner of the display.
Insert the flat end of a spudger between the front display bezel and the plastic rim attached to the rear bezel near the lower left corner of the display.
<strong>Do not</strong> insert the spudger between the plastic rim of the rear display bezel and the aluminum rear display bezel plate.
'''Do not''' insert the spudger between the plastic rim of the rear display bezel and the aluminum rear display bezel plate.
http://d3nevzfk7ii3be.cloudfront.net/igi/PMjnKwL6hPuVvI22
With your spudger still inserted under the front display bezel, run it around the lower left corner of the display.
With your spudger still inserted under the front display bezel, run it around the lower left corner of the display.
Rotate the spudger away from yourself to pry the rear display bezel off the aluminum tabs on the front display bezel.
Rotate the spudger away from yourself to pry the rear display bezel off the aluminum tabs on the front display bezel.
Work your way down the side of the display until the rear display bezel has been separated from the front display bezel.
Work your way down the side of the display until the rear display bezel has been separated from the front display bezel.
http://d3nevzfk7ii3be.cloudfront.net/igi/T2ZlClBAqbScNtaJ
http://d3nevzfk7ii3be.cloudfront.net/igi/KHf4NpwuZxyyCHXn
Insert the flat end of a spudger between the rear display bezel and the clutch cover.
Insert the flat end of a spudger between the rear display bezel and the clutch cover.
Twist the spudger to unclip the rear bezel from the clutch cover.
Twist the spudger to unclip the rear bezel from the clutch cover.
http://d3nevzfk7ii3be.cloudfront.net/igi/FDdmhC5ZlRKDpjjE
Repeat the previous steps to separate the right side of the rear display bezel from the display.
Repeat the previous steps to separate the right side of the rear display bezel from the display.
Use your spudger to pry the plastic retaining clips on the rear display bezel over the raised aluminum tabs on the front display bezel.
Use your spudger to pry the plastic retaining clips on the rear display bezel over the raised aluminum tabs on the front display bezel.
At this point, the clips on the left and right edges of the rear display bezel should be free from the raised aluminum tabs on the front display bezel. If they are not, use a spudger to pry them past the front display bezel.
At this point, the clips on the left and right edges of the rear display bezel should be free from the raised aluminum tabs on the front display bezel. If they are not, use a spudger to pry them past the front display bezel.
http://d3nevzfk7ii3be.cloudfront.net/igi/Id22BsZ3MkWFV4Uf
http://d3nevzfk7ii3be.cloudfront.net/igi/rtIqI4QY1SPqskmb
Slightly lift the lower edge of the rear display bezel and push it toward the top edge of the display, releasing the clips along the top edge of the rear display bezel.
Slightly lift the lower edge of the rear display bezel and push it toward the top edge of the display, releasing the clips along the top edge of the rear display bezel.
Rotate the rear display bezel toward yourself and lay it flat on the table.
Rotate the rear display bezel toward yourself and lay it flat on the table.
http://d3nevzfk7ii3be.cloudfront.net/igi/ZGFALBrOHDkAkIwU
http://d3nevzfk7ii3be.cloudfront.net/igi/54LVJEYmCgrIKYbv
http://d3nevzfk7ii3be.cloudfront.net/igi/YcqwrhWZAKVg1wLx
Lift the antenna board out of the clutch cover.
Lift the antenna board out of the clutch cover.
http://d3nevzfk7ii3be.cloudfront.net/igi/t6lHaZAyRHa4hZGH
Peel back the three edges of the antenna board cover and remove it from over the antenna board.
Peel back the three edges of the antenna board cover and remove it from over the antenna board.
http://d3nevzfk7ii3be.cloudfront.net/igi/ZVmMBkhHVW35nVVc
http://d3nevzfk7ii3be.cloudfront.net/igi/CZopRscMKGUOQELv
Use the flat end of a spudger to pry both antenna connectors up off the antenna board.
Use the flat end of a spudger to pry both antenna connectors up off the antenna board.
The black antenna connects near the center of the antenna board.
The black antenna connects near the center of the antenna board.
http://d3nevzfk7ii3be.cloudfront.net/igi/m2lOrqQiWc4CaMSv
http://d3nevzfk7ii3be.cloudfront.net/igi/EYb6VEqTwRZPJB5Z
If necessary, remove the two pieces of tape covering the inverter leads.
If necessary, remove the two pieces of tape covering the inverter leads.
http://d3nevzfk7ii3be.cloudfront.net/igi/hAdmaTh5MGaMDEig
The inverter is an extremely thin circuit board that is very delicate and easily cracked. Take care when handling.
The inverter is an extremely thin circuit board that is very delicate and easily cracked. Take care when handling.
Use a spudger to raise the end of the inverter out from the clutch cover.
Use a spudger to raise the end of the inverter out from the clutch cover.
Lift the inverter enough to access both cable connectors.
Lift the inverter enough to access both cable connectors.
http://d3nevzfk7ii3be.cloudfront.net/igi/UgZkfTVv3raBVFRR
http://d3nevzfk7ii3be.cloudfront.net/igi/pcLLIXby5qC1KPpx
Disconnect both inverter cables by pulling their connectors away from the sockets on the inverter.
Disconnect both inverter cables by pulling their connectors away from the sockets on the inverter.
Remove the inverter from your display and set it aside.
Remove the inverter from your display and set it aside.
http://d3nevzfk7ii3be.cloudfront.net/igi/EFAMqIUKGUhOZPeT
http://d3nevzfk7ii3be.cloudfront.net/igi/fK6nG3W2MxyyFrm2
Remove the five Phillips screws securing the LCD retaining bracket to the front display bezel.
Remove the five Phillips screws securing the LCD retaining bracket to the front display bezel.
Lift the LCD retaining bracket off the front display bezel.
Lift the LCD retaining bracket off the front display bezel.
Some machines do not have this bracket. If your machine is missing the bracket, remove the five screws and proceed to the next step.
Some machines do not have this bracket. If your machine is missing the bracket, remove the five screws and proceed to the next step.
http://d3nevzfk7ii3be.cloudfront.net/igi/LS1KpMvAjYWPJ1f2
http://d3nevzfk7ii3be.cloudfront.net/igi/5QOwnEGcsYfkmn4U
The clutch cover is constructed from aluminum and is held on to the clutch hinges with metal clips that require a good deal of force to remove. Proceed with caution.
The clutch cover is constructed from aluminum and is held on to the clutch hinges with metal clips that require a good deal of force to remove. Proceed with caution.
Use your thumbs to push the clutch cover away from the clutch hinges.
Use your thumbs to push the clutch cover away from the clutch hinges.
While pressing with your thumbs, rotate the clutch cover toward yourself about its long edge to pop it off the clutch hinge.
While pressing with your thumbs, rotate the clutch cover toward yourself about its long edge to pop it off the clutch hinge.
It may be necessary to wiggle the clutch cover while pressing it away from the clutch hinges to release the retaining clips.
It may be necessary to wiggle the clutch cover while pressing it away from the clutch hinges to release the retaining clips.
http://d3nevzfk7ii3be.cloudfront.net/igi/PTEwjhMqUlGmuR6V
http://d3nevzfk7ii3be.cloudfront.net/igi/TBH3qUOoVvBuqMIJ
Repeat this process for the other side of the clutch cover. Once the clutch cover is completely free from the clutch hinges, lift it off the front display bezel.
Repeat this process for the other side of the clutch cover. Once the clutch cover is completely free from the clutch hinges, lift it off the front display bezel.
When replacing the clutch cover, be sure to route the display data cable so that it is inside the clutch cover and extending out the end between the hinge and the display frame.
When replacing the clutch cover, be sure to route the display data cable so that it is inside the clutch cover and extending out the end between the hinge and the display frame.
http://d3nevzfk7ii3be.cloudfront.net/igi/KsDc2ghH2Zap2xea
Remove the three T8 Torx screws securing the right clutch hinge to the front bezel.
Remove the three T8 Torx screws securing the right clutch hinge to the front bezel.
http://d3nevzfk7ii3be.cloudfront.net/igi/xHSqtMagJvrtCDVI
Remove the right clutch hinge from the front bezel.
Remove the right clutch hinge from the front bezel.
http://d3nevzfk7ii3be.cloudfront.net/igi/bMi4IBZGeCK4BLHZ
To reassemble your device, follow these instructions in reverse order.