Mac mini Model A1283 Optical Drive Replacement
http://d3nevzfk7ii3be.cloudfront.net/igi/TCwdGoJLGXX5srK2
Walter Galan
Moderate
Mac mini Model A1283
Upgrade or replace the combo or SuperDrive.
Upgrade or replace the combo or SuperDrive.
1.5" Thin Putty Knife
Phillips 00 Screwdriver
Spudger
12.7 mm SATA 8x SuperDrive
Installing Mac mini Model A1283 Top Housing
Installing Mac mini Model A1283 Internal Frame
Installing Mac mini Model A1283 Optical Drive
You can skip this step if you bought your <a href="/Tools/1-5-Inch-Thin-Putty-Knife/IF145-007?utm_source=ifixit_guide&utm_medium=wiki_text&utm_term=if145-007&utm_content=product_link">putty knife from iFixit</a>. Putty knives purchased from iFixit come with pre-ground edges.
You can skip this step if you bought your [product|145007|putty knife from iFixit]. Putty knives purchased from iFixit come with pre-ground edges.
You'll need a putty knife in order to open the case. A 1.5 inch thin putty knife will work well, but you'll want to grind the edge down. Rub the putty knife's short edge back and forth on a sheet of all purpose rough grit sandpaper (100 grit will work fine) until it attains a beveled edge.
You'll need a putty knife in order to open the case. A 1.5 inch thin putty knife will work well, but you'll want to grind the edge down. Rub the putty knife's short edge back and forth on a sheet of all purpose rough grit sandpaper (100 grit will work fine) until it attains a beveled edge.
http://d3nevzfk7ii3be.cloudfront.net/igi/6VomfNFHENoHZNtc
Carefully insert a putty knife into the crevice in between the top cover and bottom housing. Start on the left side first. Push the blade down until you meet firm resistance (roughly 3/8 of an inch).
Carefully insert a putty knife into the crevice in between the top cover and bottom housing. Start on the left side first. Push the blade down until you meet firm resistance (roughly 3/8 of an inch).
Gently enlarge the existing crevice by rotating the putty knife downward and away from the mini.
Gently enlarge the existing crevice by rotating the putty knife downward and away from the mini.
http://d3nevzfk7ii3be.cloudfront.net/igi/kwpWvO6fNaTibGXZ
http://d3nevzfk7ii3be.cloudfront.net/igi/rRVslRZDUD5WyXpQ
Repeat the prying motion until a portion of the bottom housing has been nudged upward.
Repeat the prying motion until a portion of the bottom housing has been nudged upward.
http://d3nevzfk7ii3be.cloudfront.net/igi/uRxX6WWpNYy5NjGA
Repeat the same prying procedure on the right side.
Repeat the same prying procedure on the right side.
http://d3nevzfk7ii3be.cloudfront.net/igi/PaCNZUsu3AydCyGA
The top cover should now be marginally separated from the bottom housing. Use your fingers to completely separate the two, starting with the I/O side of the mini.
The top cover should now be marginally separated from the bottom housing. Use your fingers to completely separate the two, starting with the I/O side of the mini.
http://d3nevzfk7ii3be.cloudfront.net/igi/PCBKgWZPS4R4SOAu
In the next few steps you will be removing the AirPort and Bluetooth antennas (shown in red) from the internal frame. Be very careful, as breaking the brackets will require replacing the internal frame.
In the next few steps you will be removing the AirPort and Bluetooth antennas (shown in red) from the internal frame. Be very careful, as breaking the brackets will require replacing the internal frame.
We will first remove the AirPort antenna, located in the lower left corner of this picture.
We will first remove the AirPort antenna, located in the lower left corner of this picture.
http://d3nevzfk7ii3be.cloudfront.net/igi/BImvKPe44yuo1xPa
Slightly squeeze the two retaining arms toward each other and lift the AirPort antenna off its post.
Slightly squeeze the two retaining arms toward each other and lift the AirPort antenna off its post.
Squeezing the two posts excessively will surely break them off the internal frame. Work delicately.
Squeezing the two posts excessively will surely break them off the internal frame. Work delicately.
During reinstallation, you will have to slightly squeeze the two posts together so they fit into the openings on the AirPort antenna board.
During reinstallation, you will have to slightly squeeze the two posts together so they fit into the openings on the AirPort antenna board.
http://d3nevzfk7ii3be.cloudfront.net/igi/yKEqHVj2BUwoaXj3
http://d3nevzfk7ii3be.cloudfront.net/igi/5HIMyts4XJnO3qfg
The two Bluetooth antenna boards simply lift off the internal frame.
The two Bluetooth antenna boards simply lift off the internal frame.
Grab the Bluetooth antenna nearest the port side of the computer by the edges of the board and pull it straight up off the internal frame.
Grab the Bluetooth antenna nearest the port side of the computer by the edges of the board and pull it straight up off the internal frame.
Pull carefully, as it may offer significant resistance and release suddenly.
Pull carefully, as it may offer significant resistance and release suddenly.
http://d3nevzfk7ii3be.cloudfront.net/igi/2HV43KVErx5XkFd4
http://d3nevzfk7ii3be.cloudfront.net/igi/nSLY1YUSKeOFLgrf
Remove the antenna board near the front of the mini by pulling it straight up off the internal frame.
Remove the antenna board near the front of the mini by pulling it straight up off the internal frame.
If necessary, remove the piece of tape securing the antenna leads to the internal frame.
If necessary, remove the piece of tape securing the antenna leads to the internal frame.
Be sure to keep track of the springs under each of the three antenna boards.
Be sure to keep track of the springs under each of the three antenna boards.
http://d3nevzfk7ii3be.cloudfront.net/igi/ILrvud5QKPbmXR5s
Use the flat end of a spudger to pry the audio ribbon cable connector up off the audio board.
Use the flat end of a spudger to pry the audio ribbon cable connector up off the audio board.
http://d3nevzfk7ii3be.cloudfront.net/igi/xZqMSGxgYEGMmWyy
Remove the four Phillips screws securing the internal frame to the bottom housing.
Remove the four Phillips screws securing the internal frame to the bottom housing.
The screw in the lower right corner of this image is recessed deep in the internal frame and longer than the other three screws. A flashlight and a thin screwdriver aid in removal.
The screw in the lower right corner of this image is recessed deep in the internal frame and longer than the other three screws. A flashlight and a thin screwdriver aid in removal.
http://d3nevzfk7ii3be.cloudfront.net/igi/r4GF1P6Mm4LuPwaX
Lift the internal frame off the bottom housing, starting at the rear edge, until you feel the concealed edge connector on the motherboard disconnect. Then lift straight off, minding the bluetooth and 802.11 antenna cables.
Lift the internal frame off the bottom housing, starting at the rear edge, until you feel the concealed edge connector on the motherboard disconnect. Then lift straight off, minding the bluetooth and 802.11 antenna cables.
http://d3nevzfk7ii3be.cloudfront.net/igi/BoYXElgcNAvW2Mlc
Use the tip of a spudger to remove the black electrical tape spanning the interconnect board and optical drive.
Use the tip of a spudger to remove the black electrical tape spanning the interconnect board and optical drive.
http://d3nevzfk7ii3be.cloudfront.net/igi/jPOIvZDLtuPmagQV
http://d3nevzfk7ii3be.cloudfront.net/igi/1jCW54fHtvRIVHPI
Use the flat end of a spudger to disconnect the audio ribbon cable from the interconnect board.
Use the flat end of a spudger to disconnect the audio ribbon cable from the interconnect board.
http://d3nevzfk7ii3be.cloudfront.net/igi/2Dsw16GgmnWMregJ
If necessary, remove the yellow kapton tape covering the internal frame and the optical drive.
If necessary, remove the yellow kapton tape covering the internal frame and the optical drive.
http://d3nevzfk7ii3be.cloudfront.net/igi/3chLOaWVbCOUyaYR
Remove the two Phillips screws securing the optical drive to the internal frame.
Remove the two Phillips screws securing the optical drive to the internal frame.
http://d3nevzfk7ii3be.cloudfront.net/igi/efckDRFEwGJQVuuB
Turn the mini 180 degrees and remove the two Phillips screws securing the optical drive to the internal frame on the other side.
Turn the mini 180 degrees and remove the two Phillips screws securing the optical drive to the internal frame on the other side.
http://d3nevzfk7ii3be.cloudfront.net/igi/cI6LRBdRyYTNVleC
Remove the two Phillips screws securing the interconnect board to the optical drive.
Remove the two Phillips screws securing the interconnect board to the optical drive.
http://d3nevzfk7ii3be.cloudfront.net/igi/H4LKNUNkTmM2OxxK
Insert the flat end of a spudger into the crevice between the optical drive and the interconnect board.
Insert the flat end of a spudger into the crevice between the optical drive and the interconnect board.
Carefully increase the crevice to disconnect the optical drive from the interconnect board.
Carefully increase the crevice to disconnect the optical drive from the interconnect board.
http://d3nevzfk7ii3be.cloudfront.net/igi/1Y34Nm5qxHDZsJZO
Gently lift the optical drive out of the internal frame.
Gently lift the optical drive out of the internal frame.
http://d3nevzfk7ii3be.cloudfront.net/igi/bX3OL6xWxX12Defm
Transfer the four foam bumpers to the replacement optical drive.
Transfer the four foam bumpers to the replacement optical drive.
http://d3nevzfk7ii3be.cloudfront.net/igi/TCwdGoJLGXX5srK2
To reassemble your device, follow these instructions in reverse order.