I need to know what screwdrivers do I need for an HP pavilion x360 convertible 14m-dh1xxx?

was wondering if any cr2032 battery will work and what would last the longest and not damage the system?

Hallo zusammen

Habe bei einem Duplexdruck vergessen, den Stoff, der oben auf dem Drucker lag abzunehmen. Darum gabs Papierstau.

Ich habe schon oft Papierstau entfernt. Diesmal hat es nicht geklappt.

Ich kann das Papier sehen, wenn ich die hintere Klappe öffne. Ich konnte auch Teile davon rausziehen, manches mit Pinzette. Dabei habe ich bereits ein kleines orangefarbenes weiches Stück von einer Rolle erwischt. Das Papier klemmt zu weit Innen fest, hinter den weissen Rollen.

Um meinen Drucker nicht weiter zu verletzen, möchte ich ihn nun so weit auseinander nehmen, dass ich das Papier entfernen kann.

Und danach möchte ich ihn wieder zusammen gesetzt bekommen.

Gibts dazu eine Anleitung? Das wäre Klasse!

Gruss, Barbara

This is the first time i’m doing this, but i’m gonna need to replace the back cover of my HP pavillion. This is mostly due to a crack that started forming a few months ago and i’m scared the screen might pop off. Is there a guide avalible to help me? I’m also not really sure over tools, so if anyone could give any suggestions, i’ll take them gladly.

For specifications, this is the specific model: HP Pavillion x360 Convertible 15-cr0xx.

Thank you for your time.

Edit: I wasn’t so specific in my question, so i’ll add some extra details. The part that needs replacing is the back of the LCD screen. Also. this is the best image i can find of the damage

Hi,

I’m wondering if anyone can help. We have an LG 55UH850V. The tv has a problem where the screen goes black and the sounds stays on, when looking at with a torch you can see an image. I have replaced the edge lit backlight and changed the power board but still have the same issue. Can anyone point me in the direction of what to try next? Could it be I’ve installed a faulty backlight? The metal strip at the bottom of the tv (where the backlight is) seems to get really hot. Should a backlight be hot? Could the main board also cause this issue?

Thanks in advance for any replies.

=== ===

HI all i have a old veiwsonic va912 used as a extended desktop in a 4 monitor set up, a bit ago it started powering off then on again without any user input. im not exatly new to motitor problems so have managed to narow it down first a discription of the fault

1. after the monitor is powered on from cold it will run no probs for 5 min or so
2. after this it will turn its self off competly no power leds no turning back on if i press power botton its as if the power cable is unpluged
3. after 30-60 secs it will power back on
4. after 30-60 secs it will power off again and this will reapeat indefenatly
5. so after some looking around i found this site and a forum that seemed to have same issues as mine the main marked up ansew was yes its prob the power board buy a new one, one of the other ansewers did metion it could be a overheat problem so i striped the monitor again (id already had it in bits and did a visual inspetion for bulged caps with no look) and did note that some solder joints had burnt, so i resoldered and the prob was still there but with the board exposed the screen stayed on for longer, and with a fan blowing on it it stayed on indefenatly though after some time it got very buzzy noise wise and lots off tiny horazotal lines started to blurr the picture.
6. so i belive some of the CAPs are bad is there a way to test them? well on board ive orderd a multi pack of CAPs but would like to narrow it down obviose start are the solder joints that were burnt, id rather not just replace all of them as i am boand to runn in to this prob again at some point and would like to know a effechent way of narrowing it down and only replaceing bad CAPs
7. Thanks for reading and Thanks for any responses
8. im going to strip a tv with a smashed screen and see if any of the CAPs are the right size and report back with any thing i find Thanks again all :)

Hi all,

I purchased a electric bike (It is a Freestyler 3rd Gen 14”) recently and I love it, but it doesn’t charge.

I have run it down to completely 0% where the motor no longer spins, then I plug it in and the light on the charge stays green (it is meant to turn red).

(This is the first time I am trying to charge it)

I have left it plugged in over night and it has got no charge.

what happens is when I plug it ion the indicator on the bike goes up to 100%. So the bike thinks it doesn’t need charge and doesn’t charge.

I found out if I turn on the motor while it is plugged in the light goes red and charges while the motor is spinning, but then wheel i turn off the motor it goes back to a green light and it doesn’t charge.

If anyone has any ideas to help that would be very greatly appreciated.

Thanks

Hi there!

I am getting desperate! My freezer-fridge keeps freezing over. Everything checks out good and I’ve had the chip checked. The only thing I can figure is that the heating element is getting hot enough. Is that a thing? How hot do the elements get? I can just touch mine, so I assume its only heating to 105-110 F is that how hot it should be?

Thank you!!

My Sony SLV-D201P DVD/VHS Player works fine with VHS but the DVD has vertical lines running through the picture and the display is in black and white.

Hello everyone, hope someone here might be able to help me reach a solution to this problem.

I have a HP 15-cc023cl laptop here that won’t power on. When a known working charger is plugged in, the charger LED on the laptop stays off but 19v does reach the motherboard from the dc-in jack.

The charger did have some damage to the cords but has been repaired properly and is in perfect working order with 19v reaching the charger plug. The battery is brand new as the old battery was swollen and needing replacement.

I tried disconnecting all cables from the motherboard except for the main dc-in cable, just to see if any of the other components might have had a short somewhere but to no avail. Charger LED still stays of when the charger is plugged in and laptop won’t power on.

I’m pretty sure the motherboard has a shorted component somewhere on the board causing the trouble. I used diode mode on my multimeter to check the power rail coils and all the coils seem to be in perfect working order, as well as the capacitors and resistors.

I am pretty much lost at this point of the process of finding the fault and could really use some help to find the faulty component.