iPhone 3GS Volume Button Replacement

Replace the plastic volume button cover on your iPhone 3GS.

Use this guide to replace the plastic volume button cover, not the electronic volume switches themselves.

Image #1

Edit Step 1 Battery  ¶ 

  • Remove the two 3.7mm Phillips #00 screws from the dock-connector end of the iPhone.

Image #1

Edit Step 2  ¶ 

  • Remove the metal handle from the suction cup. It's easier and safer to grip the suction cup's base instead of the metal handle.

  • Be very careful when opening the iPhone so that the cables under the display are not severed.

  • There is a rubber gasket between the silver front bezel and black display assembly. A bit of force is required in this step to separate the iPhone's display assembly. It may help to rock the suction cup back and forth to remove the display assembly.

  • Use a small suction cup near the Home button to gently pull up the bottom portion of the iPhone's display assembly.

  • If the display assembly is too damaged to allow the suction cup to adhere, tape with a strong adhesive such as duct tape or packing tape may be used.

Image #1

Edit Step 3  ¶ 

  • The display assembly is still connected to the iPhone by several cables, so don't try to remove it entirely just yet.

  • Rotate the display assembly up until it is at an angle of approximately 45 degrees.

Image #1

Edit Step 4  ¶ 

  • Continue to hold the display assembly with one hand, and use your other hand and a spudger to disconnect the black ribbon cable labeled "1". (Cable 1 is for the display)

    • Be careful to insert the spudger from the left, as shown in the picture (UNDER THE RIBBON). If you try to pry up the ribbon from the right, you could damage the ribbon connector and need to replace the display!

  • All connectors except the ribbon connector mentioned in step 6 release upwards.

Image #1

Edit Step 5  ¶ 

  • Rotate the display assembly up until it is roughly vertical. This will allow easier access for disconnecting the remaining cables.

  • Use a spudger to disconnect the black ribbon cable labeled "2". (Cable 2 is for the capacitative touch panel)

Image #1

Edit Step 6  ¶ 

  • Please note: You may find on some non-American (Chinese, European) versions of the 3G that the flip up plastic tab does not exist. In this case you would slide the ribbon cable towards the screen until it is removed. When you assemble it, you would apply pressure to the ribbon to insert it back into the ribbon "socket."

  • Some iPhones may have the connector colors reversed (black plastic tab, white connector) for connector "3". Make sure you're flipping up the tab properly, otherwise you may damage the connector.

  • Use a spudger to flip up the white plastic tab holding the ribbon cable "3" in place. The white tab will rotate up 90 degrees, releasing the ribbon cable.

  • Slide the black ribbon cable out of its connector, and remove the display assembly from the iPhone.

Image #1

Edit Step 7  ¶ 

  • Insert your SIM eject tool or a paper clip into the hole next to the headphone jack.

  • Press down on the tool until the SIM card tray pops out.

  • Grasp the SIM card tray and slide it out of the iPhone.

Image #1

Edit Step 8  ¶ 

  • Use a spudger to disconnect the ribbon cable labeled "4."

Image #1

Edit Step 9  ¶ 

  • Use a spudger to disconnect the ribbon cable labeled "5."

Image #1

Edit Step 10  ¶ 

  • Use a spudger to disconnect the ribbon cable labeled "6."

  • If you have an iPhone 3GS, refer to the second picture and use a spudger to disconnect the ribbon cable labeled "7."

Image #1

Edit Step 11  ¶ 

  • Carefully peel up the small sticker labeled "Do not remove."

Image #1

Edit Step 12  ¶ 

  • Remove the following 8 screws:

    • Five 2.3 mm Phillips #00 screws with partial threads securing the logic board to the rear case.

    • Two 2.3 mm Phillips #00 screws with full threads securing the logic board and camera.

    • One 2.9 mm Phillips #00 screw from beneath the "Do not remove" sticker.

  • Note for re-assembly:

    • The screw that goes next to the camera (bottom right orange highlighted screw) also has a metal strip that holds the camera in place.

    • Remember to put this strip back in place before you insert the 2.3 mm Phillips #00 screws with full thread next to the camera

Image #1

Edit Step 13  ¶ 

  • Use a spudger to gently pry the camera up and out of its housing in the rear case.

  • The camera cannot be removed entirely yet because it's connected to the bottom of the logic board.

Image #1

Edit Step 14  ¶ 

  • Use a spudger to gently pry up the end of the logic board closest to the dock connector.

  • There is a small golden grounding tab on logic board adjacent to the 'do not remove sticker'. Be VERY careful this does not snag on the side of the case when prying up the logic board; it breaks easily. If you have signal problems after removing the logic board, check this ground tab.

  • If the board won't lift up, double check to make sure all the screws securing the logic board have been removed.

Image #1

Edit Step 15  ¶ 

  • Slide the logic board towards the dock connector and out of the iPhone.

  • When replacing the logic board after installing battery, connect the camera to the logic board before inserting it into the case. Then make sure to set the top section of the logic board (where the SIM tray is) in place before settling the rest of the board in place. This is important, as sometimes the SIM card slot will not align into place. Once the top section is in place, the bottom section can be maneuvered into place. You will know the logic board is correctly installed when the SIM tray is aligned with the opening in the iPhone case and the camera module seats neatly into its place.

Image #1

Edit Step 16  ¶ 

  • Use a spudger to pry the battery up from the rear case. The battery is attached with an adhesive strip around the perimeter of the battery. To prevent the battery from bending during the removal process, we recommend against using just the plastic pull-tab . *Note: Removing the battery is NOT necessary for replacing the GPS antenna. It merely gives you more space for removing the headphone assembly (which is also unnecessary to completely remove).

  • The iPhone's battery is attached to the rear case with a mild adhesive. This adhesive usually comes out attached to the battery. If your replacement battery already includes an adhesive backing, you're all set. If your replacement battery doesn't have an adhesive backing, you'll want to transfer the adhesive from your old battery to the new one.

  • You can use a hair dryer or heat gun on its lowest setting to heat the back of the case. This will help loosen the adhesive bond before using the spudger to separate the battery from the case back.

Image #1

Edit Step 17 Headphone Jack  ¶ 

  • Remove the two Phillips #00 screws securing the on/off switch to the front bezel.

  • When replacing, check the protrusion of the switch. There is a small plastic spacer adhered to the inside of button which may come off with cleaning. Without a spacer, the button may not protrude enough to be depressed. If lost, it can be replaced with a suitable thickness of stiff plastic (eg shirt box lid).

Image #1

Edit Step 18  ¶ 

  • Carefully peel up the orange ribbon cable from the rear case.

  • The ribbon cable is easily damaged - be very gentle.

Image #1

Edit Step 19  ¶ 

  • Remove the following 4 screws:

    • Three 1.8 mm Phillips #00 screws securing the headphone jack and GPS antenna to the rear case. Note the order in which you remove the screws, as the left one has a slightly larger head.

    • One 3.8 mm Phillips #00 screw in the plastic loop near the headphone jack.

Image #1

Edit Step 20  ¶ 

  • Remove the four Phillips #00 screws securing the volume and mute switch.

  • The volume switch assembly sits on top of the mute switch. Make sure that the small soft pad on the mute switch is not lost, otherwise the mute switch will sit very loosely after reassembly.

  • The mute switch assembly screws should be tightened with the switch in the off position. Check the protrusion of the switch when turned on, since it may not stick out far enough to operate if the switch assembly is incorrectly positioned. (Check the gap between the switch frame and the bezel (white gap showing between the two screws near the 6). The screw on the far right is slightly longer than the other 3 screws. When reassembling the phone, keep this in mind.

Image #1

Edit Step 21  ¶ 

  • Lift the volume button circuitry away from the side of the iPhone, and carefully peel up the orange ribbon cable from the rear case. The cable is thin and easily damaged.

Image #1

Edit Step 22  ¶ 

  • Carefully lift the headphone jack assembly out of the iPhone.

  • Switch the green mute switch down (towards the back side of the iPhone) into mute position. This will make it much easier to insert it, once the new mute button is in place.

Image #1

Edit Step 23 Volume Button  ¶ 

  • If they have not already fallen out of the rear case, remove the mute button and the power button.

Image #1

Edit Step 24  ¶ 

  • Remove the two Phillips #00 screws securing the vibrator to the rear panel.

  • Remove the vibrator from the rear panel.

Image #1

Edit Step 25  ¶ 

  • Remove the following 3 screws:

    • Two 1.5 mm Phillips #00 screws, one on either side of the dock connector.

    • One 2.4 mm Phillips #00 screw near the ribbon cable labeled "4."

  • Lift the dock connector assembly up and out of the iPhone.

  • When inserting the new assembly, ensure the screw holes of the assembly rest ABOVE the bezel's holes.

Image #1

Edit Step 26  ¶ 

  • In the following steps, you will partially remove the silver bezel attached to the rear panel. If the residual adhesive is not enough to hold it together during reassembly, it may be necessary to apply a light layer of glue around the inner edge of the bezel to keep it secured against the rear panel.

  • Insert the edge of an iPod opening tool into the gap between the silver bezel and the front panel on the volume button side of the phone.

  • Run the edge of the opening tool along the seam to separate the two components. The goal is to lift the silver bezel enough to push the volume button into the rear case.

Image #1

Edit Step 27  ¶ 

  • Once you have lifted the silver bezel enough to clear the volume button, use the edge of your opening tool to push the volume button toward the inside of the rear panel.

  • Remove the volume button.

To reassemble your device, follow these instructions in reverse order.

For more information, check out the iPhone 3GS device page.

Required Tools

Spudger

$2.95 · 50+ In stock

Phillips #00 Screwdriver

$5.95 · 50+ In stock

Plastic Opening Tools

$2.95 · 50+ In stock

Small Suction Cup

$2.95 · 50+ In stock

Related Products

iPhone 3G and 3GS Volume Button

$4.95 · 41 In stock

Recommended Tools

Universal Drive Adapter

$29.95 · 50+ In stock

iFixit Lock Pick Set

$29.95 · 50+ In stock

Inspection Scope

$39.95 · 50+ In stock

Frictionless Ratchet

$24.95 · 50+ In stock

Portable Anti-Static Mat

$34.95 · 39 In stock

Comments Comments are onturn off

Shesh - why doesn't the first line of step #1 say "Turn off your phone" by holding the power button down and shutting it down. I know you don't HAVE to do this, but it certain didn't feel right opening a device while the screen was humming along looking at me.

mattfife, · Reply

The power button is broken... that is why?

Marc Tobe,

You might also want to have a little tweezer which comes in very handy when reassembling the phone

Mathias, · Reply

Do seriously consider ESD when getting to the internals. External connectors have ESD protection circuits, but these will not help if you touch the internals!

HaJo Schatz, · Reply

I highly recommend using a slew of refrigerator magnets to hold the screws for each step. I also used post its to label each step, making reassembly a snap.

In the end, I was able to successfully replace the jack, but they weren't kidding when they said it was difficult.

christine, · Reply

The small suction cup near the home button didn't quite work for me, but i found some kind of workaround: just use the suction of your iPhone-carkit (if you have one)

matthias, · Reply

Duck Tape also works. :)

Matt Butson, · Reply

How should i say, do this step really really slow and with patience.

P.S. Ducktape fix nearly everything

Andi , · Reply

Be very very careful with this step. The back of connector 4 (barely visible in the Step 2 photo) was stuck just enough to the back of the display unit to shear the connecter cable right in two when I separated the phone. Ack!

Mikael S, · Reply

Be really careful at this point not too pull too hard when you're trying to get the screen out - I did, the screen came out suddenly and I pulled all the connectors off :/

Tom George, · Reply

put your fingers at power button end of phone, resting on edge of glass/bezel you can use them as lever so when you pull on suction at other end you don't need to apply much pressure and the cables underneath aren't ripped off

pollytintop, · Reply

As a help to doing this step, put your thumb/fingers around the phone around the middle so it's cradled in your hand. Keep your fingers wrapped around and resting gently on the top of the screen with your thumb and the first few fingers. See how his thumb is sitting on the edge like that, but ready to 'catch' the screen when it comes up? Do that with your thumb and the tips of your fingers on the other side.

Now carefully use the suction cup to 'walk/rock' the screen out with a left-to-right while pulling up motions. With your fingers gently clamped around the phone and providing a little pressure on the edges overlapping the screen when the screen comes out, they'll catch the screen before you pull it up too far and yank the cables out.

mattfife, · Reply

I was very careful, but not careful enough removing the display with a suction cup, and Everything came unplugged in an instant. CAUTION: Pull with the suction cup near the round button, AND ALSO have someone else support the other end of the display so that only the end of the display with the round button comes out. I was very lucky.

David Mitchell, · Reply

I put on a piece of duct tape on the Iphone where the Sim tray is. Keeps the display assembly in place preventing cable damage.

johnplim, · Reply

When you get back to this step as you are reassembling it, it's tempting to test that you've got all the cables plugged in properly by switching the phone on and testing it. However the Home button will not work until the front panel is back in position, because the electrical connection is done by a pair of touch contacts which only work when the phone is assembled.

Jon Evans, · Reply

When the instructions say "Rotate the display assembly up until it is at an angle of approximately 45 degrees." they really mean "TILT THE HOME BUTTON END OF display assembly up until it is at an angle of approximately 45 degrees. Looking at the picture makes this step brain dead simple, but if you were using another iPhone to read the directions it would be easy to miss.

ratioswitch, · Reply

What part is 1? My seems to keep dropping out and the ear speaker is not working. Is this what it is?

Russell Graham, · Reply

What are the flex cables #1, #2 and #3 for? There's a lot of questions about this, but no answers?!

SOMEONE has to know!?

Turbo Fredriksson, · Reply

Quote from Turbo Fredriksson:

What are the flex cables #1, #2 and #3 for?

Aparently #3 is 'Earpiece & Proximity Sensor'.

Turbo Fredriksson, · Reply

Quote from Turbo Fredriksson:

Aparently #3 is 'Earpiece & Proximity Sensor'.

Found the thread: http://www.ifixit.com/Answers/View/10591...

1. Ribbon #1: Runs the LCD

2. Ribbon #2: Runs the digitizer

3. Ribbon #3: Earspeaker and various sensors on the iPhone face

Turbo Fredriksson, · Reply

Note that The connectors have a rubber-like Top surface. Make surre The spudger is inserted underneath that rubber piece. To disconnect, The connector ha to lifted upwards from the PC-Board (i.e. Orthogonally from the electronics board, as opposed to being moved sideways). holds true for all of those connectors, except for the one with the flip-tab.

martinkoschel, · Reply

I had more joy using a home-made spudger from a bamboo skewer. Being thinner, it can release the connectors from the end rather than a side or corner. (I also tried all the different spudgers made by Menda Tools.)

cheongi, · Reply

At step 5 my ribbon crumbled. I had nothing left to replace. I now have a dead spot on the screen.

billsly, · Reply

On my 3G, the piece that flips up on the #3 connector was black and the connector itself was white, seemingly opposite of the pictures. I mistakenly tried to pry up the wrong piece, but fortunately didn't do too much damage before I realized this. My phone was replaced on warranty in February so this must be the case in some newer 3G's.

lolsen4, · Reply

Quote from lolsen4:

On my 3G, the piece that flips up on the #3 connector was black and the connector itself was white, seemingly opposite of the pictures. I mistakenly tried to pry up the wrong piece, but fortunately didn't do too much damage before I realized this. My phone was replaced on warranty in February so this must be the case in some newer 3G's.

Thanks for the heads-up. I added a note so that people are aware that the colors may be reversed.

Miroslav Djuric, · Reply

That flip tab on the #3 connector split in half and came off completely. Be careful. And if anyone knows where to buy a replacement flip tab, that'd be cool too :)

cliffcurtis, · Reply

I should also note that I used a little flat head screwdriver when lifting the flip tab and the narrow pressure point is what cause it to split. Should of used a spudger.

cliffcurtis, · Reply

I bought my black iPhone a full housing white cover off ebay. No phone shops seem to be able to change it for me.

If I follow this guide, will I be able to pull my phone apart, change the covers and put it back together?

That is, once I pull the phone apart, will it work properly once I put it back together again?

kristymic, · Reply

Quote from kristymic:

I bought my black iPhone a full housing white cover off ebay. No phone shops seem to be able to change it for me.

If I follow this guide, will I be able to pull my phone apart, change the covers and put it back together?

That is, once I pull the phone apart, will it work properly once I put it back together again?

Yes, if you take care and follow the instructions to the letter.

marmalade, · Reply

How on earth do I get the black ribbon cable back into its connector???

Cor Berkelaar, · Reply

Quote from Cor Berkelaar:

How on earth do I get the black ribbon cable back into its connector???

Cor, You have to slide the little bar on the connector away from the body of the connector before you can insert the ribbon cable into it. I know it's tight quarters, but even my meat hooks were able to finally get it inserted. The 'trick' is that once you have inserted the cable into the body of the connector, quickly slide the bar back toward the body as this will lock the cable into the connector. I hope this is helpful.

David

dheady, · Reply

Is there a way of replacing the connector?

i have torn the top of the connector......... would that be the reason that the iPhone would not start even though the ribbon is in the connector and fastened secured with the white plastic tab is down.

Vishal Vaidya, · Reply

I HAVE DONE IT GUYS SO THANK YOU.

Quote from Vishal Vaidya:

Is there a way of replacing the connector? i have torn the top of the connector......... would that be the reason that the iPhone would not start even though the ribbon is in the connector and fastened secured with the white plastic tab is down.

Vishal Vaidya, · Reply

Quote from Vishal Vaidya:

Is there a way of replacing the connector?

You could replace it. That's what I'll have to do. Luckily my brother is great with soldering surface mounted components.

But if you had to ask if it can be replaced, you don't have knowledge to do it yourself! It's VERY difficult! Look among your friends or the 'Net. I found quite a lot of forums where they talk about the difficulty on replacing SMD's. Just mail one of them that seem to know what they're doin'...

Turbo Fredriksson, · Reply

Quote from cliffcurtis:

if anyone knows where to buy a replacement flip tab, that'd be cool too :)

http://www.earth2k.com/fpc-ribbon/

http://cgi.ebay.com/ws/eBayISAPI.dll?Vie...

I'm currently waiting for mine... :)

Turbo Fredriksson, · Reply

[quote|I'm currently waiting for mine... :)[/quote]

And my younger brother managed to replace it with only a couple of minutes whining about it's size :).

Works just fine now (exept that I can't seem to turn the darn thing off, even though I've also replaced the button harness!)

Turbo Fredriksson, · Reply

I have torn the top of the connector too and the iPhone is not starting.. Was that the reason? Did it work after replacing the connector?

Quote from Vishal Vaidya:

Is there a way of replacing the connector? i have torn the top of the connector......... would that be the reason that the iPhone would not start even though the ribbon is in the connector and fastened secured with the white plastic tab is down.

veloudo, · Reply

Quote from lolsen4:

On my 3G, the piece that flips up on the #3 connector was black and the connector itself was white, seemingly opposite of the pictures. I mistakenly tried to pry up the wrong piece, but fortunately didn't do too much damage before I realized this. My phone was replaced on warranty in February so this must be the case in some newer 3G's.

Maybe it adds Value to the explanation to say that the piece that needs to be flipped up is located on the opposite side of where the ribbon cable exits the connector. It needs to flip upwards towards the ribbon cable.

My confusion was to identify which connector I have in my phone, since everything in there is so tiny that it is hard to identify which is which. Maybe a zoom-in on the connector with the tab flipped up would be a good addition to the instructions also.

martinkoschel, · Reply

I accidentally lost the black plastic tab (mine was black) when I was removing the ribbon cable. I managed to get the ribbon cable back into the white connector and the phone seems to be working fine. Is this going to be a problem?

Mike, · Reply

Note: You cannot slide the black ribbon connector back into place unless the lock is flipped open (up)--see the instructions on replacing a broken screen for images)

czubko, · Reply

The tab (black in my case) is the thin horizontal plastic piece opposite where the ribbon is inserted. Use the spudger in the center, approaching from the bottom side of the phone, and it flips up easily.

larry, · Reply

Be VERY careful when working with ribbon 3. I thought I was but when I got the phone back together the earpiece didn't work. While doing research to find out why, I discovered that ribbon 3 is very delicate and easy to damage. I'm now waiting for a new one... if I can't fix it, I'll have to get a new phone since I can't see myself hearing only via Bluetooth or speakerphone.

MarySC, · Reply

When re-inserting the #3 connector how much force does it take to get the connector fully inserted? How can I tell whether it is fully inserted?

slessard, · Reply

Be very careful, in some cases the ribbon damages. After this damage the proximity sensor won't work anymore.

JanWillem, · Reply

I think that this is where the problem is. I must have one of the unique (Chinese) versions and while trying to lift up, I should have been sliding back. It is too difficult to see. Mine broke off and crumbled and now the screen has a dead spot.

billsly, · Reply

That step also had me thinking & reading for quite a while. Maybe a close-up picture of the connector might be helpful, seems that a lot of people screw up badly here.

HaJo Schatz, · Reply

My American 3GS white connector did not flip open. It split into 3 little pieces of white plastic when I tried lifting it with the spudger. The plastic seemed very brittle; the phone is 4 years old. Amazingly to me, I was able to slide the flex tail back in to position and it made all the necessary electrical contacts (at least for the time being). Wi-fi cable #6 was not properly seated after first assembly, but everything is working now! Thank for the help.

Dennis Smith

denniskristen, · Reply

Can you take the SIM card out before you start the procedure?

alex, · Reply

Note! Be EXTRA careful with this cable #4. Twist and brakes easily!

taneliteittinen, · Reply

What if I have one of those thin film screen protectors applied, would the suction cup peel it right off instead of lifting the screen up?

zneumann66, · Reply

Those "6" and "7" antenna connectors are quite fragile.

Be very careful when assembling not to force the connector down; It should click actually quite easily once it's placed properly.

If you try to force the connection, it might easily be deformed, which would really be a pity.

jimbbo, · Reply

Actually, I had to apply some pressure to #7 to get it back in place - I tried not to force it as advice above said, but it wouldn't go in. The pressure wasn't too strong, but it doesn't just slide right in.

iluxan,

I think the steps to replace the connectors 6 & 7 should be emphasized because of the size/fragility of the connectors.

satsho,

I agree with the others that cable 6 and 7 are very fragile and can be difficult to reattach. I was able to get #7 back on but #6 just wouldn't attach. I put too much pressure on it so now I have a cell phone without WiFi or GPS. I would rate the repairability of this phone lower than it is because of the 50-50 chance of flattening these connectors. My 3GS is now effectively an iPod, but with a new battery.

plink53, · Reply

In hindsight I should have read over the whole recipe twice and looked at the comments before starting but I didn't because I thought I could do it and was impatient. I agree that there should be warning at the top to draw attention to the multiple wires that could be damaged when you do this.

My antenna doesn't work now and there is a small metal part that looks like a letter p that fell out of my phone. I thought it wouldn't matter till my friend said it might attach the antenna. Does anybody know where it is supposed to go?

tumaru, · Reply

Would it be a 'show-stopper' that my sticker had completely welded itself to the board and had to be removed? I carefully removed all traces of it with the spludger. When reassembled, I couldn't see the screw in contact with anything other than the ribbon cable labelled "7" (3GS). I guess it might be more a 'tamper' than anything else.

pottsrichard, · Reply

The sticker has an incredibly strong adhesive and tears very easily since it is so thin. You only need to remove the sticker enough to access the screw beneath so you don't actually need to remove the sticker so much as you need to peel it away from the screw.

ratioswitch, · Reply

What part is the number 6 label?

Bryan, · Reply

Quote from Bryan:

What part is the number 6 label?

Wireless antenna connector.

trevor, · Reply

To clarify, Connector #6 differs between the 3G and 3GS models as follows:

* 3G: GPS

* 3GS: GPS, WiFi, & Bluetooth

On the 3G model, WiFi and Bluetooth were part of the antenna sticker in the Dock Assembly which included Cellular/WWAN. On the 3GS, WiFi and Bluetooth were moved up to Connector #6 and Cellular/WWAN was kept in the same place, but attached to the new Connector #7.

shaun,

Notice "Do not remove" is important meaning when reassemble the phone get this sticker back on the screw head or use some kind of isolator like duck tape.

If not you might experience frequent unintended resets of your iPhone.

Mathias, · Reply

I had "7" button connector on mine, which is not pictured here. It was covering the "Do not remove" label

brianedow, · Reply

My DoNotRemove sticker was very hard to remove and in the end several tiny pieces tore away. I cut a piece of electric tape (same size of the sticker) and put it on top of what was left of the DoNotRemove sticker. No problems so far (it has been 4 days).

hsm6second, · Reply

One of the two full thread screws holds a small retention clip not shown in this diagram to keep the camera in place (3G model). Remove this clip when removing the screws.

jake2, · Reply

Please note that iFixit supplied screwdriver is way too big for these tiny screws, you'll need a smaller one like the ones used to repair wrist watches!

The good side is that iFixit's screwdriver is magnetized, a bonus when working with such small parts.

paolo, · Reply

while re assembling i couldnt for the life of me figure out where the metal plate thing off the camera went until i saw the gap for it (i had spent about half an hour trying to put it in)

jjw123, · Reply

My Camera is not working anymore =( going to open my iphone once again...

l4ci, · Reply

I found that after putting the battery in place and reattaching the logic board with the screws I had to press down a little bit to get the screws to reach because the battery contacts kept the logic board from settling in this tension gives positive contact between board and battery.

Bill, · Reply

I am unable to remove the screw that holds the camera in place. I'm afraid I am stripping the screw head. Any advice?

libchis, · Reply

After removing the 2.3 mm Phillips #00 screw attached to the camera a small retaining clip may be present.

Take note of its position and orientation for later reinstallation.

John Zemko, · Reply

As mentioned, some 3g phones there is a small metal clip holding down the camera (held in place by the screw there). Be sure it doesn't fly out or fall into the phone workings. Fine point tweezers would help here, to take it out and to put back in place during re-assembly.

Tim, · Reply

3G and 3GS camera enclosure: As I was transplanting a 3G cover onto a 3GS, I realized as I was trying to re-assemble the camera that it would not fit: the 3GS camera does not fit in the 3G enclosure. Luckily, you can remove just the camera enclosure from the 3GS and transplant it to the 3G. It's dirty, I broke the ring, I transplanted some of the double face tape... but in the end it worked.

chuvux, · Reply

There were many places where I wished there were clearer instructions on putting it back together; this was a big one. It was very difficult to get the camera back in place. I heard a snap when mine went into place.

atlemar, · Reply

Even after the eight screws are remove, the board won't lift up easily. That is because the golden clip nearby the "do not remove sticker". In the picture above, it simply jumped out for no reason, while I had to use a tweezer to make it out...

wandonye, · Reply

When removing the logic board, a slight push towards the top of the phone, will "unclip" the bottom edge of the logic board near the "Do Not Remove" screw.

When reinserting the logic board, there is a tab in the top edge of the rear shell case that the edge of the logic board goes under. It is the edge closest to the camera.

Without this "comfortable" fit, you won't be able to get the SIM in.

The camera itself also has an element of "comfortable" Fit.

Fritz, · Reply

Be careful when putting the circuit board back in also... the golden grounding tab is very easy to break...

rclyons, · Reply

When reversing directions for reassembly, the logic board needs to be clipped into the clips on the side.

Lenore, · Reply

Quote from Lenore:

When reversing directions for reassembly, the logic board needs to be clipped into the clips on the side.

++

Although I would say "needs to be slipped under the clips on the side". The most obvious clip is next to the camera, facing south (if the camera is in the NE corner). There is a corresponding clip on the opposite side of the north end the logic board, facing east (a bit east of the #6 ribbon cable).

It's still possible to get all the screws back in with the logic board above the clips (trust me), but it's a serious barnus because the SIM card holder won't fit back in and the camera will be pointing a bit askew ... and you'll have to pull all the screws back out and figure out what you did wrong (and why you had a naggling suspicion the logic board wasn't placed quite right).

I would recommend sliding in the SIM card tray *before* putting any screws back, just to make sure.

johnhart, · Reply

Slipping the SIM card in first is a helpful suggestion.

My motherboard actually was not quite lined-up as mentioned, and so after the SIM didn't fit, I was able to pull and reposition the motherboard properly before proceeding.

Quote from johnhart:

++

Although I would say "needs to be slipped under the clips on the side". The most obvious clip is next to the camera, facing south (if the camera is in the NE corner). There is a corresponding clip on the opposite side of the north end the logic board, facing east (a bit east of the #6 ribbon cable).

It's still possible to get all the screws back in with the logic board above the clips (trust me), but it's a serious barnus because the SIM card holder won't fit back in and the camera will be pointing a bit askew ... and you'll have to pull all the screws back out and figure out what you did wrong (and why you had a naggling suspicion the logic board wasn't placed quite right).

I would recommend sliding in the SIM card tray *before* putting any screws back, just to make sure.

ianwright, · Reply

When putting it back together, it helps with alignment to put in the SIM Card tray. This beats having all your screws back in and finding out it's misaligned. Put the logic board 5/6 the way in, and insert the SIM Card tray like normal. Allow it to guide your logic board into the proper place.

Mathew Taylor, · Reply

When re-installing the mother board ensure that all of the previoulsly diconnected connector cables are out of the way and do not become trapped by the motherboard.

Tom Brandolini, · Reply

Definitely watch out to have all your connectors above the board. I managed to get my #5 connector trapped under it. Still hope wasn't damaged, we'll see in a few minutes :)

iluxan, · Reply

check also that the golden cicuit is opened when the sim card tray is inserted. this circuitry controls the presence of the sim card tray.

maxt, · Reply

The glue is very strong under the battery and you may end up snapping a few spudgers in the process so make sure you have a few spare for moving onto other steps. A screwdriver is to hard and will end up damaging the battery.

viper501, · Reply

Splendid job. it was like a walk. perfect Instructions.

A tip: to handle the screws, very small, I used a pair of tweezers for eyebrows wrapped in double sided adhesive tape.

Thanks. Alessandro

AlexPi, · Reply

Well, I took the chance and the LCD broke on this step. Called iFixit and they advised, "Oh well". $60 well spent during these trying times. Hey, I have a great little screwdriver.

taylor431, · Reply

How could the LCD break on this step? It was removed and set aside many steps ago.

Terence Elliott, · Reply

it is said on step 18 "Carefully peel up the orange ribbon cable from the rear panel"

but when you reassemble the iPhone, how do you glue the ribbon on your new panel?

bobbyfrog, · Reply

I successfully completed these steps to dry out a wet phone. While everything inside was dry as a bone, I never did remove the battery since the adhesive was so strong.

I found the spudger far too weak to even attempt the removal of the battery. Instead, I used a folding bone (something I've had for years that's used for making perfect folds in heavy printmaking paper) however, I was still bending the battery far more than I was comfortable with. Since my mission was not to mess with or replace the battery anyways I just left it alone.

Excellent directions!

ratioswitch, · Reply

Installed and the phone is working... You'd think Apple didn't want us to be able to replace the battery. Good directions.

lazygorilla, · Reply

I did not need to remove the battery. The power button, headphone jack, volume rocker, and vibrate switch were all accessible with the battery still in place.

Mike M, · Reply

I've done all the steps and phone switches on and works just fine with the one exception that I do have a signal! Is it possible I've damaged the aerial in the process? The strange thing is that on checking the networks I can see T-Mobile, but not 02, so implies something is working. All very odd. Currently my iPhone has become an iPod! Erkk

Any tips?

John, · Reply

You most likely forgot to re-atatch the antenna. It is one of the connecters you unhooked after the first 3...its located in the top left of the case..Its a circular connecter.

Quote from John:

I've done all the steps and phone switches on and works just fine with the one exception that I do have a signal! Is it possible I've damaged the aerial in the process? The strange thing is that on checking the networks I can see T-Mobile, but not 02, so implies something is working. All very odd. Currently my iPhone has become an iPod! Erkk

Any tips?

Charles Ravaglia, · Reply

Sorry...Its the connecter on the bottom left..Rectangular shaped

Quote from John:

I've done all the steps and phone switches on and works just fine with the one exception that I do have a signal! Is it possible I've damaged the aerial in the process? The strange thing is that on checking the networks I can see T-Mobile, but not 02, so implies something is working. All very odd. Currently my iPhone has become an iPod! Erkk

Any tips?

Charles Ravaglia, · Reply

I put back together my iPhone and put it in a new shell but I just finished and the power button won't work what could i have done wrong?

thomas manning, · Reply

Quote from thomas manning:

I put back together my iPhone and put it in a new shell but I just finished and the power button won't work what could i have done wrong?

oh also the vibrate button won't work any ideas there?

thomas manning, · Reply

I managed to replace the mute button without removing the on/off button :o)

luisgarcillan, · Reply

Great tutorial guys, I must admit it's not easy, due to tiny parts and screws, but you can do it!

Great!

KrissWeb, · Reply

Was able to peel the ribbons without removing the battery. Worked great with a 3G. Thanks

midiman127, · Reply

Instructions and notes made this fairly easy to do. I had one scary moment where my screen would not turn on but a Hard Reset on the phone fixed it.

richardskevinm, · Reply

any help welcome,just changed the battery on the wife's iPhone after it took a little swim,it wouldn't charge after drying out and i thought a new battery would be the answer,phone switches on ok and everything works except it won't charge on any of our proven chargers.guess something on the main board's knackered. if you have any ideas i would be a very happy chap.

gareth jones, · Reply

Be careful when trying to pry the battery from the side, as the spudger will break.

zeke, · Reply

There are no delicate parts below the battery so you can push the spudger under the battery without damaging anything. Just be careful at the top of the phone that you don't damage the orange ribbon cable.

Erik Mouw, · Reply

Just a little tip I thought I might add. I would recommend having a digital camera handy to taking snap shots before proceeding with each step, so that you can see exactly how it originally looked at each stage. Once you've gotten to the battery section, just pop the card from the camera into a computer or applicable device and you now have a simple guide for reassembly that is specific to your device.

Also, it may be prudent to take a picture of the screws laid out in a tray along side the phone in the same positions they came out of.

szr, · Reply

Agree with others - spooger will almost certainly break if you try to pry it out using just that and you can't pull hard enough on the plastic tab. Even on my 2 year old phone, the glue was still *quite* good at holding the battery in.

I used an equally small flat-blade screwdriver and gently walked around the battery lifting against the bottom plastic and the edge of the phone being careful NEVER to touch any of the flat-cable wires. While you can pry against the bottom since there is nothing under it (just double-check since there are some wires running along the side of the phone and the pressure you need to remove the battery would damage the wires if you pryed on them), you need to be careful against the edge of the phone. It's cheap plastic. You can pry against it, but I dared not use more force than enough to start hearing the adhesive start to rip/creak loose. SLOWLY walking around the battery at safe pry points several times finally loosened it enough that I could pull it out. GO SLOW.

mattfife, · Reply

I found removal of the batt was easier to accomplish by prying slightly and slowly around, starting from the edge opposite the Volume control.

Fritz, · Reply

Same - the key is to start prying with a screwdriver, not a plastic spudger, but make sure to keep away from any wires.

iluxan,

If you have the plastic spudger that comes in the kit, it will most likely break when trying to remove the battery. A butter knife worked extremely well, however ...

jargogle, · Reply

Agree with this comment. Prying the battery up from its adhesive was the hardest part of this repair, and yes, I did break the spudger thingy.

Barb,

Make sure no unplugged cabel is under the circute board when inserting the board again.

This happens easily since the cable tend to spring back.

Mathias, · Reply

Since I didn't have a hair dryer (never needed one) I used a 500W construction lamp... Those things get very hot. The battery came free relatively easy.

DefCharlie, · Reply

Had to use pliers to slowly pull the battery free by it's tab. When you reverse the steps to reassemble the phone - make sure to get all 6 (or 7 for the 3GS) cables plugged back in. I forgot connector 5 and had to take the phone back apart. Then realized the next day I also had missed connector 6 (wifi). So because I reassembled too quickly the first time - I got to do all the steps 3 times! But phone works perfectly now with a new battery.

pdusini, · Reply

Actually broke the plastic spludger trying to get the battery off. Considered it the hardest part of the tutorial. I kept looking at it to see if I hadn't ruined something.Asides from this, reassembling was fairly quick although there was no sliding back of the logic board for me on a 3G. Turned it back on, tested sound, microphone and wifi. All seems good. Thanks alot for all the help guys.

pedromcerveirapinto, · Reply

I've made all the disassembling process with no problems, but when I put the logic board back the battery starts getting hot and hotter. Any suggestions??

germanperezsalva, · Reply

When I put the new battery in, it was a smidge too far toward the bottom. As a result the logic board didn't quite fit back into place and I was unable to put two screws back in. However, the repair seems successful and my phone is working now. Additional guidance on installing the battery would help.

atlemar, · Reply

So, I replaced the battery, but now, when I charge the phone, it shuts down and restarts. It also shuts down with use. Hmmm. What is it? Is it the "Do not remove tape"? Or som eother connector?

jonatgree, · Reply

Im stuck at reassembling the power on/off button after replacing the jack connector, for me its the most difficult part because it can be assembled partially wrong and then it won't turn it on. Could anyone post some more details about it ? for instance how the button itself should be placed and what screw should be used, by mistake I had some screws mixed and now I don't recognize which one should be used. THANKS!

Nicola Ferruzzi, · Reply

This Step is not really necessary.

Christian Schiefer, · Reply

Always test the button after replacement, if its not moving freely, loosen both sides or take one screw out, and refit, its like the mute switch, sometime it takes a few times of refitting to get it right. On new cases, especially the OEM kind, you might have to "scrape" a bit of the plastic where the button goes through to get it to move more freely.

Mark, · Reply

Hi guys!

I have set of new screws here an I need to sort them - I can't find any specifications on the two screws mentioned here. How long are the two screws for the "on/off"-swith exactly? Thanks for the hlep, this website is great!

JulianFixIt, · Reply

Can somebody say me, if the screw (1.8 mm) on the left side is very important? I lost this screw? What is the function of this screw?

joachimschreiter, · Reply

4 screws: If the 3.8mm (orange circle) is #1

#2 and #4 are identical

#3 has a smaller head.

jimbbo, · Reply

In tight places like this, I found a teense bit of Elmers spotted on the screw head and allowed to dry a few secs to the driver, helps to stabilize the way in.

Fritz, · Reply

I can't get the orange screw loose from the headphone jack. It continuously spins, but never pops up from the assembly. I can't use tweezers to get at it because despite unscrewing it forever, the head never comes away. How do I fix this?

Jessi Darklighter, · Reply

Try to lever the screw's head with a flat screwdriver or a knife, so you can force it outwards while you screw it lose. That usually works with stripped screws.

Dirk Lucas, · Reply

For step 20, not all of the screws in my phone were the same length. The far right screw in the picture is a longer screw than the others.

Mike M, · Reply

by the time you are removing the vibrate button, you should check this to be in ¨off¨ position, as is a small part and is a very triky situation re-assembling this, it fits back, it doesnt matter if is on or off so you will realise this by the time you have the iPhone completed and couldnt use the button, result, open again and correct it.

alberto Carrillo, · Reply

Hi All,

I continue on my iPhone build and I fix one part and seem to break another.

After stripping it all down I then put it all back together but now my lock button doesnt work.

Any ideas?

I followed the tutorial and the rest of the buttons on the ribbon all work.

What could of happened?

Liam George, · Reply

While disassembling, the screw in the far right corner should be separated from the other screws. If you confuse it with one of the other three screws, it is impossible to reassemble the vibration button.

roemer71, · Reply

What meaning by "off" position? Vibration off, or sound off?

Brian, · Reply

When reassembling I found the screwhole for the longer screw (on the right) was full of glue. I used a hot pin to get the worst of it out.

paulmillin, · Reply

Hi guys, my middle screw on my volume button is stuck and I don't want to keep unscrewing it for fear of wearing the head down too much. Does anyone have any hints that might help me? Cheers!

Aaron, · Reply

Hi guys!

I have set of new screws here an I need to sort them - I can't find more detailled specifications on the four screws mentioned here. How long are the screws for the sound-swith exactly? How long is the "slightly longer" screw on the far right? Thanks for the hlep, this website is great!

JulianFixIt, · Reply

This is a great guide in helping you dismantle the phone and to remove the existing assembly, however the bit that's actually difficult is not covered, which is installing the new one...when a get a few more minutes I'll write a detailed description of how I did this is and the things to watch out for (it took me bloody ages). Any questions in the meantime feel free to message me!

Joe Fleming, · Reply

Quote from Joe Fleming:

This is a great guide in helping you dismantle the phone and to remove the existing assembly, however the bit that's actually difficult is not covered, which is installing the new one...when a get a few more minutes I'll write a detailed description of how I did this is and the things to watch out for (it took me bloody ages). Any questions in the meantime feel free to message me!

Would love to read your writeup and tips for installing the replacement. Thanks, Bernard

bvc7g, · Reply

Joe, I'd really appreciate any advice/instruction on that most complicated part of the operation! Seems to be nowhere on the net that gives this info. I've taken the iPhone to pieces and put it back together as the part I had and the part it's meant to be replace just looked worlds apart (though they were identical on closer inspection).

Sure others here would love to know as well.

Cheers!

Andy

iggy1967 *at* hotmail.com

iggypop, · Reply

I'm having a hard time reversing this process. I've got the switch set to "off" and I think I've got everything in the right spot, put a few screws back in, and the switch sits flush against the side the case, instead of coming out a bit. Being flush it's switch it on and off. Any suggestions? Please!

Alan Tocheri, · Reply

Guys, I really need help! I've managed everything -including replacing all the plastics etc. onto the new headphone replacement and it's all almost ready to go ...apart from the power button!! How the devil do you fit it back on?? I've tried every combination and am staggered that i can't find a single resource online that covers this.

I'd be in your debt if you could help -and I'm sure there are others here too who'd appreciate it!

iggypop, · Reply

Power button is a little funny. The button itself has that metal "swing" (for lack of a better word) to it. If you push the "swing" as far as you can from side to side, you'll notice it doesn't move as far from one side to the other. So we'll call these the 'short side' and 'long side'.

The button goes into the back of the phone with the 'long side' of the swing faces the back of the phone. So when you put it in, the metal swing will be facing down, fitting into the grove in the back plate.

The switch with the 2 screws just fit over top of it. It doesn't seem like it would work, but put them in and try the button. It should give you the 'click' and normal feedback you'd expect.

Clear as mud?

Alan Tocheri, · Reply

Alan,

I have taken everything apart but cannot figure out how to release the ribbon from the vibrate button? How does this part come off and how does the new one go on?

Thanks,

Austin

austinochs,

From what I remember, the ribbon doesn't come off from the vibrate button or volume button. I believe it's one piece when you go to replace it. Someone might be able to correct me though.

Alan Tocheri,

Alan,

Clear as a crystal! And it worked beautifully. All back together now -many thanks;)

The vibrate has gone kaput but I think I can live with that;)

Andy

iggypop, · Reply

Well after all that my problem persists.

the iPod plays fine through the speakers, but sounds faraway in headphones -almost as if mono through both cans.

I've tried adaptors, three sets of headphones and am a little frustrated that even managing to replace the jack hasn't solved this.

There's nothing online anywhere about this problem, so...who out there has some ideas on what it could be? I'm foxed.

iggypop, · Reply

Heya, I followed the guide to replace mute button. Everything went fine until I put it together and tried to start it up. iPhone just shows apple log and it dissapears after 5 seconds. Nothing happens. Any suggestion?

Michael, · Reply

Hey Michael, so did you find a solution for this problem. I have the same Problem: Pressing PowerButton, Display turns on, Apple Logo ... and thats all? What should I do?

joachimschreiter,

By the way: When I pflug in the iPhone with my mac: Itunes could Sync my iPhone and iphoto see all the photos, which are on the camera roll. But I cannot use my phone: I only see the apple on the Display.

joachimschreiter,

On my replacement part, there were two small plastic posts on the back of the switch. Looking at the one I'm replacing and the new one, it seemed as if they needed to be squashed, but I found the solution with a soldering iron. If you carefully melt the two posts with a broad tip, you create a much firmer bond between the switch itself and the metal shoe it fits on.

Technickal28, · Reply

For me, two questions are not answered yet in this step:

It is only possible to buy a flex cable without the microswitch and the metal housing of ring/vibrate-Button. So:

1. How can I remove the small switch from the old flex cable? Only by pulling out?

2. How do I remove the metal housing? Pulling out the old plastic posts is sufficient?

iphoneschorsch, · Reply

Once the headphone jack assembly has been removed from the phone, you must remove the three brackets attached to the assembly. Pay close attention to the orientation of these brackets in relation to the small adhesive tabs on the assembly so that you can properly adhere the brackets to your replacement assembly.

Chris Rothgeb, · Reply

watch out for a small mettal washer here, i wasn't paying attention an now dont know where it goes.

nickmew, · Reply

The headphone jack slides backwards slightly before you can lift it out. Installation should push the jack down then slide into place.

Roger Soucy, · Reply

I had some trouble getting the mute switch/rocker to function properly, as a couple others have mentioned. There is only one way it will work properly: Make sure the mute rocker is in the muted position with the red dot visible before you re-install the bracket. The switch that you stuck to the bracket by removing the tape backing must also be in the muted position (pushed down toward the back of the case). The tip of the switch fits into a hole in the rocker. If it isn't in the hole, moving the mute rocker will dislodge the taped switch from the bracket. Take your time with this step and make sure the mute rocker feels normal before attaching anything else (phone jack, power button, etc.). Good luck!

goodski, · Reply

I have also experienced that the adhesive located on the "mute/silence" button is really bad on some aftermarket parts. I have had good results using a small drop of "loctite superglue" in addition to the adhesive. (Please be sure to avoid getting any glue on the actual button..).

Iver, · Reply

Having a magnetized screw driver would have saved me about 15 minutes (puting the phone back together) - otherwise, I used tweezers to set each screw in to position before tightening (carefully)

jeeames, · Reply

This guide doesn't cover installing the new vibrate switch that comes as part of a new ribbon cable assembly, so a quick couple of things to note:

1) The vibrate/silent switch on the end of the ribbon cable is secured in place by a solid metal bracket. This bracket holds the switch against the outer plastic vibrate/silent rocker. When you pull out the old ribbon cable assembly, the metal bracket will come with, it is welded on by plastic lugs on the back of the switch. Don't fear, if you have a soldering iron you can melt these away and gently pull off the old switch and ribbon cable assembly.

2) Installing the new switch/ribbon cable assembly is a bit tricky. The back of the new switch should have an adhesive pad and two fresh plastic lugs. Stick the switch onto the bracket to hold it in place and then carefully melt the plastic lugs down with the flat of the soldering iron to weld the switch in place. Be careful not to apply too much heat to the switch, and don't burn your fingers! It's pretty fiddly to hold. You will want to ensure the switch is firmly welded on, otherwise there will be some play in the vibrate switch action.

AmusedToDeath, · Reply

View Statistics:

Today: 11

This Week: 57

This Month: 560

All Time: 76,172