Installing MacBook Core 2 Duo Left I/O Frame

  • Author: iRobot
  • Difficulty: Moderate
  • Add Note x
  • x 6

The frame over your ports.

Sections
Tools
first image

Add Note Edit Step 1 — Battery  ¶ 

  • Use a coin to rotate the battery-locking screw 90 degrees clockwise.

first image

Add Note Edit Step 2  ¶ 

  • Lift the battery out of the computer.

first image

Add Note Edit Step 3 — Memory Cover  ¶ 

  • Unscrew the three evenly-spaced Phillips screws from along the rear wall of the battery compartment.

  • The screws are captive to the metal memory cover so you cannot lose them.

first image

Add Note Edit Step 4  ¶ 

  • Rotate the L-shaped memory cover so it clears the battery compartment opening and lift it up and out of the computer.

first image

Add Note Edit Step 5 — Upper Case  ¶ 

  • Remove the following 3 screws:

    • One 11 mm Phillips#00 in the middle of the case. (Head: 5mm dia. x .75mm thick)

    • Two 14.5 mm Phillips #00 (Head: 5mm dia. x .75mm thick)

  • If the screws stick in the case, you can use a magnetized screwdriver to draw them out.

  • The shorter of the three screws goes in the middle.

first image

Add Note Edit Step 6  ¶ 

  • Remove the following 3 screws from the rear wall of the battery compartment:

    • One 3 mm Phillips #0. (Head: 2.75 mm. dia.)

    • Two 4 mm Phillips #0 on the either side. (Head: 2.75mm dia.)

first image

Add Note Edit Step 7  ¶ 

  • Remove the two Phillips screws from either side of the right wall of the battery compartment (not the ones closest to the battery connector).

    • Two 6.25 mm Phillips #000. (Head: 4 mm. dia. x .5mm thick)

first image

Add Note Edit Step 8  ¶ 

  • Remove the four indicated Phillips screws from the front wall of the battery compartment. When working from the left, remove the 2nd, 4th, 7th and 9th screw.

    • Four 3.25 mm Phillips #000. (Head: 4 mm. dia. x 4mm thick)

first image

Add Note Edit Step 9  ¶ 

  • Remove the following 4 screws from the back of the computer:

  • The longer screws go on the inside, shorter screws on the outside.

    • Two 11 mm Phillips #00, with Shank (2.2mm dia. x 2 mm len.) (Head: 3.2 mm. dia. x .5mm thick)

    • Two 7.25 mm Phillips #00, with Shank (2mm dia. x 3.75 mm len.) (Head: 3.2 mm. dia. x .5mm thick)

first image

Add Note Edit Step 10  ¶ 

  • Remove the two Phillips screws from the optical drive side of the computer.

    • Two 5.2 mm Phillips #00, with Shank (2.3mm dia. x 3.5 mm len.) (Head: 3.2 mm. dia. x .5mm thick)

  • It is not necessary to remove the similar screws on the other side of the computer.

first image

Add Note Edit Step 11  ¶ 

  • There's a trackpad and keyboard ribbon connecting the upper case to the logic board, so don't pull the upper case off entirely just yet.

  • Starting near the display and working around to the front of the computer, pry up on the upper case. A plastic opening tool or a medium hard guitar pick may help you to do this.

  • The upper case is likely to stick at the connection above the optical drive. If this is the case, first free all other sides, then proceed to pull upward on the upper case from either side of the optical drive opening.

first image

Add Note Edit Step 12  ¶ 

  • While holding up the upper case, pull up the black tab of the silver cable away from its connector.

  • If there is no black tab, you can also use a spudger to gently pry the connector from its housing. This connector is tall, so be sure to pry straight up.

  • If you happen to break your upper case cable when removing the upper case, we stock the cable individually and we have a guide that makes replacing it easy.

first image

Add Note Edit Step 13 — Left I/O Frame  ¶ 

  • Disconnect the MagSafe board cable from the logic board by pulling the snap-in connector out (to the right).

first image

Add Note Edit Step 14  ¶ 

  • Remove the single 9 mm Phillips screw securing the left speaker to the lower case.

  • Lift the left speaker out of its housing and set it to the side.

first image

Add Note Edit Step 15  ¶ 

  • Remove the following 3 screws:

    • Two 9 mm Phillips from either end of the left I/O frame.

    • One 7.5 mm Phillips from the middle of the left I/O frame.

  • Remove the small black plastic spacer at the bottom of the left I/O frame.

first image

Add Note Edit Step 16  ¶ 

  • Lift the left I/O frame up and out of the computer. Pay attention to the thin metal EMI fingers, as they may catch as you remove the left I/O frame.

  • The speaker wire may be hooked onto the I/O frame. Lift it out of the catch and don't forget to put it back when you are reversing the procedure.

  • The part of the shield you are removing is attached to other part by little hooks underneath that are hard to see until you have it apart. They're located over the headphone jack and the firewire port

To reassemble your device, follow these instructions in reverse order.

For more information, check out the MacBook Core 2 Duo device page.

Did you successfully follow this guide?

Notes Add Note Notes are offturn on