PlayStation 3 Blu-ray Disc Drive Replacement

Replace a burned-out Blu-ray drive on your PS3.

Use this guide to replace your PlayStation 3's Blu-ray disc drive. Replacing a defective Blu-ray drive with a replacement requires swapping the Blu-ray drive board from the old drive onto the replacement.

Image #1

Edit Step 1 Smart Plate  ¶ 

  • Use the tip of a spudger to remove the black rubber screw cover from the side of the PS3.

Image #1

Edit Step 2  ¶ 

  • Remove the single 8.5 mm T10 Security Torx screw from the smart plate.

Image #1

Edit Step 3  ¶ 

  • Pull the smart plate toward the hard drive bay, then lift it off the body of the PS3.

Image #1

Edit Step 4  ¶ 

  • Be sure to keep track of the small metal bracket loosely held in the top cover, if equipped.

Image #1

Edit Step 5 Top Cover  ¶ 

  • Remove the following seven screws:

    • Six 52 mm Phillips screws

    • One 30 mm Phillips screw

Image #1

Edit Step 6  ¶ 

  • Lift the top cover from its rear edge and rotate it toward the front of the PS3.

  • Remove the top cover.

Image #1

Edit Step 7 Blu-ray Disc Drive  ¶ 

  • Disconnect the Blu-ray power cable from the motherboard.

  • Pull the connector straight up and out of its socket.

Image #1

Edit Step 8  ¶ 

  • Lift the Blu-ray drive from the edge nearest the power supply and rotate it away from the chassis enough to access its ribbon cable.

Image #1

Edit Step 9  ¶ 

  • Use your fingernail to flip up the retaining flap on the Blu-ray ribbon cable socket.

  • Be sure you are prying up on the retaining flap, not the socket itself.

  • Pull the ribbon cable out of its socket.

  • Remove the Blu-ray drive from the PS3.

  • If replacing the Blu-ray drive, transfer the power cable to your new drive.

To reassemble your device, follow these instructions in reverse order.

For more information, check out the PlayStation 3 device page.

Required Tools

Spudger

$2.95 · 50+ In stock

Phillips #1 Screwdriver

$5.95 · 50+ In stock

Recommended Tools

Universal Drive Adapter

$29.95 · 50+ In stock

iFixit Lock Pick Set

$29.95 · 50+ In stock

Inspection Scope

$39.95 · 50+ In stock

Frictionless Ratchet

$24.95 · 50+ In stock

Portable Anti-Static Mat

$34.95 · 40 In stock

Comments Comments are onturn off

2 more smaller screws (don't know what size...small) just below the top middle screw and top right screw (in the picture). Look for the arrows...

E Goo, · Reply

after you remove the screws, you may have to push a tab to take the cover off if you meet resistance on one side of the cover. Here is a link to a video that explains it, saved me lots of trouble:

http://youtu.be/jZgekNsRB-A?t=1m54s

ericksi33, · Reply

Thanks @ericksi33, this really helped me out.

hogurt,

1st attempt, fan loud. Ps3 lasted about 2 wks. 2nd attempt noticed very poor contact between heatsink & cpu,gpu when taking it apart. Research - Found a better way to apply thermal past. I personally disapprove of guide on this. A small bit about the size of a grain of rice in center of cpu is plenty. Clamp the heat sinks back on. Then take it apart & check contact area. Thermal paste should have spread to about the size of a quarter.(more is better. Less then a nickel size is poor contact) possibly weak clamps. Carefully applied pressure onto the cpu & gpu, pressing them into the heatsinks before clamping heatsink clamps on. Achieved greater then quarter sized thermal past spread. Fan silent in comparison & ps3 lasted about a yr. Rarely did I ever hear the fan go to high and get loud after that. About to begin my third fix on this same ps3. One of the first 80g backwards compatible. other then those notes and that this guide was for a different model ps3 (minor differences) I liked this guide. easy to follow.

brettgomes, · Reply

Although the battery is described as proprietary, it looks like it is the common CR2032 lithium coin battery that is used in calculators and some computers. I haven't had to replace mine but I suspect under the heatshrink cover is a battery holder which will allow the coin battery to be removed and replaced. Then wrap with electrical tape and reinstall.

RickP, · Reply

Not all systems look like this, some have tape instead of the flap.

gatewaynomad, · Reply

Every system that I have seen has had the ZIF connector, while some had tape over the connection as well. If your connectors are taped, be sure to remove the tape, then proceed with undoing the ZIF connector.

Brett Hartt,

The version 2 systems baseboard PCB started switching to the new narrow 24 pin ZIF header/ribbon and Blu-Ray drive connection.

You should not attempt to detach the taped ribbon cable from the drive end first as described above for the older wide 60 pin ribbons. You must remove the drive and ribbon as one unit to protect the fragile ZIF sockets.

The slimmer fragile ribbon is taped to the drive housing to afford a more secure ZIF connection. The opposite base connection is slightly under the PSU.

continued

shadetree, · Reply

From continued

One should firstly remove the PSU: Disconnect the drive power cable as described above. Unscrew the 5 (3-P1 2-P2) PSU mounting screws. Now leaving the power cables attached, lift the PSU off the power baseboard PCB pins and move over slightly to access the baseboard drive cable end ZIF. Release the ZIF latch and slide the entire (drive and ribbon) strait away from the baseboard ZIF to disconnect.

After the complete drive/ribbon removal, you can carefully remove the restraining tape on the bottom of the drive to release the ribbon ZIF, then remove the 24 pin ribbon from the drive logic PCB.

Install in reverse order making sure to add new tape to secure the ribbon to the drive.

shadetree, · Reply

View Statistics:

Today: 21

This Week: 21

This Month: 2,332

All Time: 140,068