Motorola Droid RAZR Antenna/Headphone Jack Replacement

Droid RAZR antenna and headphone jack replacement.

The main wireless antenna and headphone jack are both located in the large plastic housing located at the top of the Droid RAZR.

Image #1

Edit Step 1 Back Cover  ¶ 

  • Insert a plastic opening tool between the back cover and rear case at the lower left edge of the back cover.

  • Pry the back cover up with the plastic opening tool to free the plastic clips.

  • Continue prying along the left edge of the back cover towards the top of the phone.

Image #1

Edit Step 2  ¶ 

  • Work the plastic opening tool across the top of the back case to free the plastic clips.

  • The top edge of the back case is very thin. Pry carefully to avoid cracking or snapping it.

  • Continue prying down the right side of the back cover to free the remaining clips.

Image #1

Edit Step 3  ¶ 

  • Pull the back cover away from the phone to remove it.

  • The back cover is attached to the battery with a generous amount of adhesive, so you may have to use quite a bit of force to separate the two pieces.

    • The battery must remain in the phone and not come off with the back cover or you will break the power lead.

  • Since the back cover is made of Kevlar, it can handle a fair amount of twisting and tugging without breaking.

Image #1

Edit Step 4 Battery  ¶ 

  • Use the tip of a spudger to lift up the red silicone cover over the battery terminal screws and remove it.

Image #1

Edit Step 5  ¶ 

  • Remove the two 3.3 mm T5 Torx battery terminal screws.

  • Grab the blue battery removal tab and lift the battery out to remove it.

  • There is quite a bit of adhesive securing the battery to the motherboard. Work slowly to avoid deforming the battery.

  • Your phone will have a number of metal EMI shields on the motherboard, rather than the bare ICs seen here.

Image #1

Edit Step 6 Camera Cover  ¶ 

  • Use a heat gun or hair dryer to soften the adhesive underneath the camera cover.

    • The following steps were performed without the use of a heat gun. Notice that the camera cover cracks very easily if you do not heat the adhesive that holds it in place.

  • Gently pry up the bottom edge of the camera cover with a plastic opening tool.

  • Carefully slide the plastic opening tool across the bottom edge to free it from the adhesive.

  • Continue to use the heat gun as needed to soften the adhesive as you remove the camera cover.

Image #1

Edit Step 7  ¶ 

  • Insert the plastic opening tool underneath the top edge of the camera cover.

  • Gently pry the camera cover up as you slide the plastic opening tool across the top edge to free it from the adhesive.

  • Remove the camera cover.

Image #1

Edit Step 8 Rear Case  ¶ 

  • Remove the six screws securing the rear case to the rest of the phone:

    • three 6.7 mm silver T3 Torx screws at the top,

    • four 4.0 mm gold T3 Torx screws in the middle,

    • and three 4.5 mm black T5 Torx screws at the bottom.

Image #1

Edit Step 9  ¶ 

  • Insert a plastic opening tool between the rear case and the motherboard assembly.

  • Work your way down the side of the phone and gently pry the rear case up.

  • Separate the rear case from the motherboard assembly.

Image #1

Edit Step 10 Motherboard Assembly  ¶ 

  • Remove the three 2.5 mm T4 Torx screws securing the metal chassis to the motherboard.

  • Remove the metal chassis from the motherboard assembly.

Image #1

Edit Step 11  ¶ 

  • Use the flat end of a spudger to remove the two red silicone microphone covers at the top and bottom of the motherboard.

Image #1

Edit Step 12  ¶ 

  • There is a small metal shield that covers the display assembly cable connectors on the motherboard. This shield is held in place by a few small clips that attach to the surrounding EMI shields.

  • Use the tip of a spudger to gently bend the clips out of shape and remove the shield.

Image #1

Edit Step 13  ¶ 

  • Use the flat end of a spudger to pry the three display cable connectors off their sockets on the motherboard.

Image #1

Edit Step 14  ¶ 

  • There are a number of small black plastic clips on the display assembly that hold the motherboard in place.

  • Release the securing clips with a plastic opening tool.

Image #1

Edit Step 15  ¶ 

  • Use a heat gun or hair dryer to soften the adhesive strip around the perimeter of the motherboard.

  • Pry the edges of the motherboard up from the display assembly with a plastic opening tool.

  • Remove the motherboard assembly.

Image #1

Edit Step 16 Rear-Facing Camera  ¶ 

  • Lift up the anti-static tape covering the camera and earpiece ZIF connectors with the tip of a spudger.

  • Peel back the tape and remove it.

  • Unless you have spare ESD-safe tape lying around, you may consider keeping this piece somewhere safe to be reused at reassembly.

Image #1

Edit Step 17  ¶ 

  • Use a plastic opening tool or your fingernail to lift up the tab on the rear-facing camera ribbon cable ZIF connector.

    • Make sure you're prying on the tab and not the connector itself.

  • Push the rear-facing camera through its hole in the grey antenna and remove it.

Image #1

Edit Step 18 Front-Facing Camera  ¶ 

  • Use a plastic opening tool or your fingernail to lift up the tab on the front-facing camera ribbon cable ZIF connector.

    • Make sure you're prying on the tab and not the connector itself.

  • Lift the front-facing camera out of the antenna with the plastic opening tool and remove it.

Image #1

Edit Step 19 Antenna/Headphone Jack  ¶ 

  • Insert a plastic opening tool between the antenna and motherboard near the micro USB and micro HDMI ports and pry the antenna free.

  • Remove the antenna from the motherboard.

To reassemble your device, follow these instructions in reverse order.

For more information, check out the Motorola Droid RAZR device page.

Required Tools

Spudger

$2.95 · 50+ In stock

Heat Gun

$24.95 · 50+ In stock

T5 Torx Screwdriver

$4.95 · 50+ In stock

T4 Torx Screwdriver

$4.95 · 50+ In stock

Plastic Opening Tools

$2.95 · 50+ In stock

Recommended Tools

Universal Drive Adapter

$29.95 · 50+ In stock

iFixit Lock Pick Set

$29.95 · 50+ In stock

Inspection Scope

$39.95 · 50+ In stock

Frictionless Ratchet

$24.95 · 50+ In stock

Portable Anti-Static Mat

$34.95 · 41 In stock

Popular Products

Probe and Pick Set

$6.95 · 50+ In stock

Pro Tech Toolkit

$69.95 · 50+ In stock

Magnetic Pickup Tool

$4.95 · 50+ In stock

Comments Comments are onturn off

I did this repair on a Droid Razr model xt912. My version has a plastic shield over the battery connectors; the shield is part of the rear case, so I had to do steps 6-9 before I could do steps 4 and 5.

kpnine, · Reply

Excellent guide, but it forgot to include that you need to get double sided adhesive to replace the old adhesive. Maybe its implied? Anyways I got mine from here: http://www.repairsuniverse.com/3m-double...

derekz732, · Reply

Is it really necessary to remove the camera cover to replace the display assembly??? Reviewing the rest of the steps to the display, I could see no reson to remove the camera cover. Of course I've not begun my own disassembly yet, but when I do I'll see if the camera cover can be left in place and let you know how it goes.

edgoldsmith2, · Reply

Yes. Check the step 8. The camera cover hide one T3 torx screw.

Enrique Ballarin,

Some phone models with have T3 torx screws (orange circles)

Brian Seielstad, · Reply

MIND YOU !

This is a mistake or the production process has been altered.

Infact, all but 3 (of all screws described as T3) are infact T4 !

You can imagine my face when I took the phone apart today and the T3 driver head didn't fit -.-

Yuri Chris Taillandier, · Reply

View Statistics:

Today: 0

This Week: 185

This Month: 481

All Time: 19,693