MacBook Pro 15" Core Duo Model A1150 RAM Replacement

Featured Guide

Featured Guide

This guide has been found to be exceptionally cool by the iFixit staff.

Two RAM slots allow up to 2 GB of PC2-5300 RAM.

Sections
Tools
Image #1

Edit Step 1 Battery  ¶ 

  • Use your fingers to push both battery release tabs away from the battery, and lift the battery out of the computer.

Image #1

Edit Step 2 Memory Door  ¶ 

  • Remove the three identical Phillips screws from the memory door.

  • Make sure to record which sets of screws came from where. This will help when re-assembling.

Image #1

Edit Step 3  ¶ 

  • Lift the memory door up enough to get a grip on it, and slide it toward you, pulling it away from the casing.

Image #1

Edit Step 4 RAM  ¶ 

  • Release the tabs on each side of the RAM chip at the same time. These tabs lock the chip in place and releasing them will cause the chip to "pop" up.

Image #1

Edit Step 5  ¶ 

  • Pull the chip directly out from its connector.

  • If there are two RAM chips installed, repeat the above procedure for the second chip.

To reassemble your device, follow these instructions in reverse order.

For more information, check out the MacBook Pro 15" Core Duo Model A1150 device page.

Required Tools

Phillips #00 Screwdriver

$5.95 · 50+ In stock

Related Products

PC2-5300 1 GB RAM Chip

$14.95 · 11 In stock

PC2-5300 2 GB RAM Chip

$34.95 · 29 In stock

Recommended Tools

Universal Drive Adapter

$29.95 · 50+ In stock

iFixit Lock Pick Set

$29.95 · 50+ In stock

Inspection Scope

$39.95 · 50+ In stock

Frictionless Ratchet

$24.95 · 50+ In stock

Portable Anti-Static Mat

$34.95 · 45 In stock

Comments Comments are onturn off

Before beginning, I found some small plastic bags and labeled each of the with the location the screws would come from once removed and the appropriate step number. Once the screws were removed I placed them in the labeled bags and did not have to worry about mixing screws up. Also, provided a good way to insure that no steps were skipped in the reverse process

rpbetancourt, · Reply

If you don't have any plastic bags, you can always print out the photos in black and white as you go, and then tape the screws on to the print outs over the circles that denote the screw positions in the photos. This method helps get every single screw back in it's exact location, even months after a tear down. ;o)

Adam, · Reply

Quote from Adam:

If you don't have any plastic bags, you can always print out the photos in black and white as you go, and then tape the screws on to the print outs over the circles that denote the screw positions in the photos. This method helps get every single screw back in it's exact location, even months after a tear down. ;o)

Thank you very much!

Evgeniy, · Reply

When I did this, I used a empty egg carton to store my screws. I wrote the steps where I removed screens in Sharpie on the bottom of the "egg cup" and then dropped the screws in as I went. Then I just worked backwards to put it all back together.

mark93, · Reply

Quote from rpbetancourt:

Before beginning, I found some small plastic bags and labeled each of the with the location the screws would come from once removed and the appropriate step number. Once the screws were removed I placed them in the labeled bags and did not have to worry about mixing screws up. Also, provided a good way to insure that no steps were skipped in the reverse process

I Generally just use a piece of paper with a rough sketch of the system and locations of the screws with prestik.

Tarn Alcock, · Reply

View Statistics:

Today: 4

This Week: 30

This Month: 213

All Time: 47,512