MacBook Pro 15" Core Duo Model A1150 Bluetooth Board Replacement

  • Author: iRobot
  • Difficulty: Difficult

Replace the Bluetooth board.

Image #1

Edit Step 1 Battery  ¶ 

  • Use your fingers to push both battery release tabs away from the battery, and lift the battery out of the computer.

Image #1

Edit Step 2 Memory Door  ¶ 

  • Remove the three identical Phillips screws from the memory door.

  • Make sure to record which sets of screws came from where. This will help when re-assembling.

Image #1

Edit Step 3  ¶ 

  • Lift the memory door up enough to get a grip on it, and slide it toward you, pulling it away from the casing.

Image #1

Edit Step 4 Upper Case  ¶ 

  • Remove the two Phillips screws in the battery compartment near the latch.

Image #1

Edit Step 5  ¶ 

  • Remove the following 6 screws:

    • Two 10 mm T6 Torx screws on either side of the RAM slot.

    • Four 14.5 mm Phillips screws along the hinge.

Image #1

Edit Step 6  ¶ 

  • Remove the four Phillips screws on the port side of the computer.

Image #1

Edit Step 7  ¶ 

  • Rotate the computer 90 degrees and remove the two Phillips screws from the rear of the computer.

Image #1

Edit Step 8  ¶ 

  • Rotate the computer 90 degrees again and remove the four Phillips screws from the side of the computer.

Image #1

Edit Step 9  ¶ 

  • Do not yank the upper case off quickly. The case is attached to the logic board via a ribbon cable.

  • Lift up at the rear of the case and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case. This stage can be quite tricky. Over the DVD reader are 4 tabs set back which pull out vertically.

  • Note that the two small tongues on the left hand front of the upper case may bend while you remove the upper case. When re-installing, you may need to bend them back to fit in the grooves in the lower case.

Image #1

Edit Step 10  ¶ 

  • Disconnect the trackpad and keyboard ribbon cable from the logic board, removing tape as necessary.

  • Remove the upper case.

Image #1

Edit Step 11 Bluetooth Board  ¶ 

  • Lift the Bluetooth board out of its slot next to the hard drive and use a spudger to disconnect the Bluetooth antenna cable.

Image #1

Edit Step 12  ¶ 

  • Slide back the translucent plastic sheath to reveal the Bluetooth data connector beneath.

  • Disconnect the orange data cable from the Bluetooth board by sliding the locking mechanism slightly to the right to free the cable, and then sliding the cable out of its connector.

To reassemble your device, follow these instructions in reverse order.

For more information, check out the MacBook Pro 15" Core Duo Model A1150 device page.

Required Tools

Spudger

$2.95 · 50+ In stock

T6 Torx Screwdriver

$5.95 · 50+ In stock

T6 Torx Screwdriver

$9.95 · 26 In stock

T6 Torx Screwdriver

$4.95 · 50+ In stock

Phillips #00 Screwdriver

$5.95 · 50+ In stock

Related Products

Recommended Tools

Universal Drive Adapter

$29.95 · 50+ In stock

iFixit Lock Pick Set

$29.95 · 50+ In stock

Inspection Scope

$39.95 · 50+ In stock

Frictionless Ratchet

$24.95 · 50+ In stock

Portable Anti-Static Mat

$34.95 · 39 In stock

Comments Comments are onturn off

Before beginning, I found some small plastic bags and labeled each of the with the location the screws would come from once removed and the appropriate step number. Once the screws were removed I placed them in the labeled bags and did not have to worry about mixing screws up. Also, provided a good way to insure that no steps were skipped in the reverse process

rpbetancourt, · Reply

If you don't have any plastic bags, you can always print out the photos in black and white as you go, and then tape the screws on to the print outs over the circles that denote the screw positions in the photos. This method helps get every single screw back in it's exact location, even months after a tear down. ;o)

Adam, · Reply

Quote from Adam:

If you don't have any plastic bags, you can always print out the photos in black and white as you go, and then tape the screws on to the print outs over the circles that denote the screw positions in the photos. This method helps get every single screw back in it's exact location, even months after a tear down. ;o)

Thank you very much!

Evgeniy, · Reply

When I did this, I used a empty egg carton to store my screws. I wrote the steps where I removed screens in Sharpie on the bottom of the "egg cup" and then dropped the screws in as I went. Then I just worked backwards to put it all back together.

mark93, · Reply

Quote from rpbetancourt:

Before beginning, I found some small plastic bags and labeled each of the with the location the screws would come from once removed and the appropriate step number. Once the screws were removed I placed them in the labeled bags and did not have to worry about mixing screws up. Also, provided a good way to insure that no steps were skipped in the reverse process

I Generally just use a piece of paper with a rough sketch of the system and locations of the screws with prestik.

Tarn Alcock, · Reply

Getting these screws in and out is difficult because most screwdrivers are longer then the battery compartment is deep and so will be slightly off plumb. When you go to re-assemble the computer, getting these screws to seat is one of the hardest parts of the re-assembly. It's very important to be gentle and not to strip the threads.The screw should tighten and come to a stop after 3-4 turns. If you turn 6 or more turns and don't feel it grab, then back off and try again, making sure that everything is in alignment.It might be easier to start with the left screw, because it is further away from the latch mechanism.

dalphotography, · Reply

A T6 worked but was too small. A T7 was better.

Nelson R Pardee, · Reply

Be careful when reassembling your laptop -- do not put the screw into the DVI port! It will not come out.

Scott Rose, · Reply

by Scott Rose Jan 4 @ 11:12 PM

Be careful when reassembling your laptop -- do not put the screw into the DVI port! It will not come out.

To keep this from possibly happening, I placed 2 pieces of tape over the DVI connector pin holes.

rpbetancourt, · Reply

Be careful in step 4, these two screws are shorter than the four screws in step 6, dont mix them up!

brendantully1, · Reply

If you still have the DVI to VGA adapter that came with the computer plug it in to the plug and screw it tight, that way you will not put one of the screws into the holes.

netdude21, · Reply

there are 2 push buttons inside the harddrive bay which release the front of the upper case.

mforgie, · Reply

this is an annoyingly difficult step. it is VERY hard to get the front part off without bending the unit improperly. Would be great to know where the two "push buttons" are.

lessig, · Reply

On my MacBook, there were no pushbuttons. Rather, two mini phillips screws were holding the case on inside the battery bay. The two screws are under two ball-bearing-like nubs that help hold the battery in the bay.

khank, · Reply

Quote from khank:

On my MacBook, there were no pushbuttons. Rather, two mini phillips screws were holding the case on inside the battery bay. The two screws are under two ball-bearing-like nubs that help hold the battery in the bay.

I just realized these were the screws mentioned in Step 4, which I missed originally. Did you miss step 4 too?

khank, · Reply

I discovered that I didn't need to take the case off completely. I just propped it up with a small screwdriver and was able to remove the airport card and replace it with a new one fairly easily.

schemedream, · Reply

That's not so difficult step. you shoul know , that front edge of upper case holding only on 5 plastic "locks" 4 in front edge upon the superdrive, 5-th near the "sleep light, open laptop button"

just lift up the rear edges of upper case to 35-40 degrees

Hofmann78rus, · Reply

[I d just say carefule on the prising open - these are fragile screw tab fixings joined to the uppercase. - Patience and gentle pressure and all works fine .

daithid, · Reply

Getting the top case off, especially right above the optical drive slot was a @#$%^. !^$%. Was finally able to work it loose by twisting in the budger. Be careful.

Archhawk, · Reply

the two push pins are in the battery area behind the front of the open button

mykeylynx, · Reply

Quote from Archhawk:

Getting the top case off, especially right above the optical drive slot was a @#$%^. !^$%. Was finally able to work it loose by twisting in the budger. Be careful.

I agree! It was really very difficult just ROCKING the front panel. NOT done! Do not pry it from the front of the unit, as the soft metal edge gets scratched! I turned the unit upside down and slowly pried the keyboard apart left-to-right from INSIDE the Battery Bay, slipping a plastic pen to keep it apart. When I finally looked at what was holding it down, it was these 5 grey&black plastic SNAP slots, and 4 of them were behind the DVD slot.

http://www.facebook.com/photo.php?pid=40...

Mario da Silva, · Reply

I found I had to push with a little force from underneath the battery compartment where the touch pad is located to free the bottom edge of the case. The case came away with two loud snaps. At first I thought I'd broken something, but then it appeared that it was just the plastic above the slot loading super drive that was held in very tightly and needed some encouragement.

Joshua May, · Reply

There are several clips along the front of the case in front of trackpad and above the optical drive slot. These need to be gently levered open (eg using an old credit card), and clipped closed on reassembly. Start at the left hand side. Take care not to bend the aluminum top. When reassembling, check the top panel for kinks/bends and straighten by hand before reassembly.

cheongi, · Reply

The way I did it was to lift the back to about 45% (the ribbon cable is long enough) and then used the spudger to force the 4 snap tabs in front of the optical drive to separate, working from the right edge towards the middle (they will 'pop'), ending with the last tab to the left of the sleep light.

Hilal Malawi, · Reply

not necessary. just attach a string around both the screen and the keyboard. it will stay in a steady position..

-urdus.

urdus, · Reply

I found that the ribbon connecting the top part of the case to the logic board wasn't long enough and the connector did have to be disconnected.

Joshua May,

Quote from urdus:

not necessary. just attach a string around both the screen and the keyboard. it will stay in a steady position..

-urdus.

Excellent tip! Thanks, this allowed me to skip steps 10 and 11 (any unnecessary tinkering with the logic board is recommended).

rpbetancourt, · Reply

View Statistics:

Today: 0

This Week: 2

This Month: 37

All Time: 7,856