With the case closed, place the Unibody top-side down on a flat surface. Depress the grooved side of the access door release latch enough to grab the free end. Lift the release latch until it is vertical. /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4447 With the case closed, place the Unibody top-side down on a flat surface. Depress the grooved side of the access door release latch enough to grab the free end. Lift the release latch until it is vertical. /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4447 The access door should now be raised enough to lift it up and out of the Unibody. /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4448 Be sure the access door release latch is vertical before proceeding. Grab the translucent plastic tab and pull the battery up and out of the Unibody. If the latch is depressed it will lock the battery in place. /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4449 Remove the following eight screws securing the lower case to the chassis: One 5.4 mm Phillips screw. Three 14 mm Phillips screws. Four 3.5 mm Phillips screws. /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4453 Using both hands, lift and remove the lower case off the upper case. /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4454 If necessary, peel the EMI gasket off the camera cable connector. Disconnect the camera cable by pulling the male end straight away from its socket toward the optical drive opening. Do not try to lift this connector straight up off the board. Pull the connector parallel to the face of the logic board. Deroute the camera data cable from the channel in the optical drive. /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4526 If necessary, peel the EMI gasket off the camera cable connector. Disconnect the camera cable by pulling the male end straight away from its socket toward the optical drive opening. Do not try to lift this connector straight up off the board. Pull the connector parallel to the face of the logic board. Deroute the camera data cable from the channel in the optical drive. /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4526 Remove the two Phillips screws securing the camera cable bracket to the upper case. The leftmost screw may remain captive in the camera cable. Seperate the camera cable bracket from the camera cable and remove it from the computer. /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4529 Remove the two Phillips screws securing the camera cable bracket to the upper case. The leftmost screw may remain captive in the camera cable. Seperate the camera cable bracket from the camera cable and remove it from the computer. /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4529 Grab the plastic pull tab secured to the LVDS cable lock and rotate it toward the DC-in side of the computer. Pull the LVDS connector straight away from its socket. When disconnecting the LVDS cable, do not pull on the black tab secured to the LVDS cable lock. We recommend wiggling the cable while applying tension to slowly "walk" the connector out of its socket. /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4530 Grab the plastic pull tab secured to the LVDS cable lock and rotate it toward the DC-in side of the computer. Pull the LVDS connector straight away from its socket. When disconnecting the LVDS cable, do not pull on the black tab secured to the LVDS cable lock. We recommend wiggling the cable while applying tension to slowly "walk" the connector out of its socket. /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4530 Remove the 7 mm Phillips screw from the LVDS cable bracket. This screw may remain captive in the LVDS cable. Lift the LVDS cable bracket out of the upper case. /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4531 Remove the 7 mm Phillips screw from the LVDS cable bracket. This screw may remain captive in the LVDS cable. Lift the LVDS cable bracket out of the upper case. /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4531 Remove the two outer 6 mm Torx screws securing each side of the display to the upper case (four screws total). /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4532 Open your MacBook Pro so the display is perpendicular to the upper case. Place your opened MacBook Pro on a table as pictured. While holding the display and upper case together with your other hand, remove the 6 mm Torx screw from the lower display bracket. /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4533 Be sure to hold the display and upper case together with your other hand. Failure to do so may cause the freed display/upper case to fall, potentially damaging each component. Remove the last remaining 6 mm Torx screw securing the display to the upper case. /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4534 Grab the upper case with your right hand and rotate it slightly toward the top of the display so the upper display bracket clears the edge of the upper case. Rotate the display slightly away from the upper case. Lift the display away from the upper case, minding any brackets or cables that may get caught. /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4535 Grab the upper case with your right hand and rotate it slightly toward the top of the display so the upper display bracket clears the edge of the upper case. Rotate the display slightly away from the upper case. Lift the display away from the upper case, minding any brackets or cables that may get caught. /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4535 Grab the upper case with your right hand and rotate it slightly toward the top of the display so the upper display bracket clears the edge of the upper case. Rotate the display slightly away from the upper case. Lift the display away from the upper case, minding any brackets or cables that may get caught. /Guide/Installing-MacBook-Pro-15-Inch-Unibody-Late-2008-and-Early-2009-Display-Assembly/837/all#s4535