Use a coin to rotate the battery-locking screw 90 degrees clockwise. /Guide/Installing-MacBook-Core-2-Duo-Magsafe-Board/520/all#s2425 Lift the battery out of the computer. /Guide/Installing-MacBook-Core-2-Duo-Magsafe-Board/520/all#s2426 Unscrew the three evenly-spaced Phillips screws from along the rear wall of the battery compartment. The screws are captive to the metal memory cover so you cannot lose them. /Guide/Installing-MacBook-Core-2-Duo-Magsafe-Board/520/all#s2427 Rotate the L-shaped memory cover so it clears the battery compartment opening and lift it up and out of the computer. /Guide/Installing-MacBook-Core-2-Duo-Magsafe-Board/520/all#s2428 Remove the following 3 screws: One 11 mm Phillips#00 in the middle of the case. (Head: 5mm dia. x .75mm thick) Two 14.5 mm Phillips #00 (Head: 5mm dia. x .75mm thick) If the screws stick in the case, you can use a magnetized screwdriver to draw them out. The shorter of the three screws goes in the middle. /Guide/Installing-MacBook-Core-2-Duo-Magsafe-Board/520/all#s2434 Remove the following 3 screws from the rear wall of the battery compartment: One 3 mm Phillips #0. (Head: 2.75 mm. dia.) Two 4 mm Phillips #0 on the either side. (Head: 2.75mm dia.) /Guide/Installing-MacBook-Core-2-Duo-Magsafe-Board/520/all#s2435 Remove the two Phillips screws from either side of the right wall of the battery compartment (not the ones closest to the battery connector). Two 6.25 mm Phillips #000. (Head: 4 mm. dia. x .5mm thick) /Guide/Installing-MacBook-Core-2-Duo-Magsafe-Board/520/all#s2436 Remove the four indicated Phillips screws from the front wall of the battery compartment. When working from the left, remove the 2nd, 4th, 7th and 9th screw. Four 3.25 mm Phillips #000. (Head: 4 mm. dia. x 4mm thick) /Guide/Installing-MacBook-Core-2-Duo-Magsafe-Board/520/all#s2437 Remove the following 4 screws from the back of the computer: The longer screws go on the inside, shorter screws on the outside. Two 11 mm Phillips #00, with Shank (2.2mm dia. x 2 mm len.) (Head: 3.2 mm. dia. x .5mm thick) Two 7.25 mm Phillips #00, with Shank (2mm dia. x 3.75 mm len.) (Head: 3.2 mm. dia. x .5mm thick) /Guide/Installing-MacBook-Core-2-Duo-Magsafe-Board/520/all#s2439 Remove the two Phillips screws from the optical drive side of the computer. Two 5.2 mm Phillips #00, with Shank (2.3mm dia. x 3.5 mm len.) (Head: 3.2 mm. dia. x .5mm thick) It is not necessary to remove the similar screws on the other side of the computer. /Guide/Installing-MacBook-Core-2-Duo-Magsafe-Board/520/all#s2440 There's a trackpad and keyboard ribbon connecting the upper case to the logic board, so don't pull the upper case off entirely just yet. Starting near the display and working around to the front of the computer, pry up on the upper case. A plastic opening tool or a medium hard guitar pick may help you to do this. The upper case is likely to stick at the connection above the optical drive. If this is the case, first free all other sides, then proceed to pull upward on the upper case from either side of the optical drive opening. /Guide/Installing-MacBook-Core-2-Duo-Magsafe-Board/520/all#s2441 While holding up the upper case, pull up the black tab of the silver cable away from its connector. If there is no black tab, you can also use a spudger to gently pry the connector from its housing. This connector is tall, so be sure to pry straight up. If you happen to break your upper case cable when removing the upper case, we stock the cable individually and we have a guide that makes replacing it easy. /Guide/Installing-MacBook-Core-2-Duo-Magsafe-Board/520/all#s2442 Remove the left 3 mm and right 8 mm (right screw is unnecessary to remove on some models) One 3.25mm Phillips #000 (Head: 4mm dia. x .5mm thick) One 8.5mm Phillips #000 (Head: 4mm dia. x .75mm thick The Phillips screws securing the MagSafe board and the left speaker to the lower case. The next two speaker steps are unnecessary one some models as are steps 16 and 17 as the magsafe will drop in without removing these. /Guide/Installing-MacBook-Core-2-Duo-Magsafe-Board/520/all#s2464 Use a spudger to lift the left speaker out of its housing. Grasp it with your fingers and set it aside. The left speaker cable is still connected to the logic board. /Guide/Installing-MacBook-Core-2-Duo-Magsafe-Board/520/all#s4058 Use a spudger to lift the left speaker out of its housing. Grasp it with your fingers and set it aside. The left speaker cable is still connected to the logic board. /Guide/Installing-MacBook-Core-2-Duo-Magsafe-Board/520/all#s4058 Disconnect the MagSafe board connector from the logic board. /Guide/Installing-MacBook-Core-2-Duo-Magsafe-Board/520/all#s4059 Remove the following three screws securing the left I/O frame: Two 7.5 mm Phillips screws from the top and bottom end of the left I/O frame. One 9 mm Phillips from the middle of the left I/O frame. On some models, all three screws may be the same size. If present, remove the black plastic spacer at the bottom of the left I/O frame. /Guide/Installing-MacBook-Core-2-Duo-Magsafe-Board/520/all#s4060 Lift the left I/O frame up and out of the computer. Pay attention to the thin metal EMI fingers, as they may catch as you remove the left I/O frame. /Guide/Installing-MacBook-Core-2-Duo-Magsafe-Board/520/all#s4061 The MagSafe board is now free of all connections and can be deteached freely from the logic board. Using your fingers, pull out the MagSafe board. /Guide/Installing-MacBook-Core-2-Duo-Magsafe-Board/520/all#s4062