Before opening your iPod, ensure that the hold switch is in the locked position. The slider should be all the way to the right if your iPod is facing you. /Guide/Installing-iPod-5th-Generation-Video-Battery/603/all#s3200 Opening the iPod can be challenging. Do not get discouraged if it takes you a few tries before the iPod is opened. Free the first retainer clip on the bottom of the iPod using the iPod opening tool. The tool's edge should point towards the metal back case to prevent scratching the plastic front. /Guide/Installing-iPod-5th-Generation-Video-Battery/603/all#s3201 There are five retaining clips on each side of the iPod. An iPod opening tool will be used to separate the plastic front from the metal back of the iPod. Insert the iPod opening tool into the left side of the iPod, with the edge of the tool pointing towards the metal back. Gently enlarge the existing crevice by wiggling the iPod opening tool and moving it to the left. Continue doing so until the entire side of the iPod is loose. You can then insert an iPod opening tool near the Hold button. Be very careful while inserting the tool, as the display is very fragile. /Guide/Installing-iPod-5th-Generation-Video-Battery/603/all#s3202 There are five retaining clips on each side of the iPod. An iPod opening tool will be used to separate the plastic front from the metal back of the iPod. Insert the iPod opening tool into the left side of the iPod, with the edge of the tool pointing towards the metal back. Gently enlarge the existing crevice by wiggling the iPod opening tool and moving it to the left. Continue doing so until the entire side of the iPod is loose. You can then insert an iPod opening tool near the Hold button. Be very careful while inserting the tool, as the display is very fragile. /Guide/Installing-iPod-5th-Generation-Video-Battery/603/all#s3202 There are five retaining clips on each side of the iPod. An iPod opening tool will be used to separate the plastic front from the metal back of the iPod. Insert the iPod opening tool into the left side of the iPod, with the edge of the tool pointing towards the metal back. Gently enlarge the existing crevice by wiggling the iPod opening tool and moving it to the left. Continue doing so until the entire side of the iPod is loose. You can then insert an iPod opening tool near the Hold button. Be very careful while inserting the tool, as the display is very fragile. /Guide/Installing-iPod-5th-Generation-Video-Battery/603/all#s3202 Gently glide the iPod opening tool on the top of the display, making sure to free the retaining clips. The other sides of the iPod should now easily come loose. If they do not, use iPod opening tools on the right side of the iPod in the same way as on the left side of the iPod. Separate the front of the iPod from the back about an inch (or a couple of centimeters). The iPod casing is now open, but don't completely separate the two halves just yet. Two ribbon cables are still connecting the back panel to the rest of the iPod. /Guide/Installing-iPod-5th-Generation-Video-Battery/603/all#s3203 Gently glide the iPod opening tool on the top of the display, making sure to free the retaining clips. The other sides of the iPod should now easily come loose. If they do not, use iPod opening tools on the right side of the iPod in the same way as on the left side of the iPod. Separate the front of the iPod from the back about an inch (or a couple of centimeters). The iPod casing is now open, but don't completely separate the two halves just yet. Two ribbon cables are still connecting the back panel to the rest of the iPod. /Guide/Installing-iPod-5th-Generation-Video-Battery/603/all#s3203 Use an iPod opening tool to slide up the brown connector holding the orange battery ribbon cable in place. You only need to lift the brown connector up about 1-2mm to free the cable. Don't lift up too far or you could pull the battery connector out of the logic board. Make sure to slide the brown connector directly upwards. The connector is frail and will break if it is accidentally shifted to the side. The connector has hooks at the bottom to hold the cable in place. As soon as you break one of the arms you will have problems putting the battery cable back on. If it breaks put the cable in the slot and then push the brown holder in place to keep the cable from slipping out. Remove the cable from the connector. /Guide/Installing-iPod-5th-Generation-Video-Battery/603/all#s3204 You should now have one orange ribbon cable still attaching the front case to the back. At this point you are able to remove and replace the blue rubber bumpers, or continue with separating the case. /Guide/Installing-iPod-5th-Generation-Video-Battery/603/all#s3205 Lift up the hard drive to expose the headphone jack ribbon connector (indicated by the yellow box). If the hard drive bumpers come loose, make sure to put them back with the notch as shown in the picture. /Guide/Installing-iPod-5th-Generation-Video-Battery/603/all#s3206 With the iPod opening tool, gently lift the brown tab of the headphone ribbon cable connector. The tab will rotate up 90 degrees, releasing the ribbon cable. Using your fingers, pull out the headphone jack ribbon cable. /Guide/Installing-iPod-5th-Generation-Video-Battery/603/all#s3207 With the iPod opening tool, gently lift the brown tab of the headphone ribbon cable connector. The tab will rotate up 90 degrees, releasing the ribbon cable. Using your fingers, pull out the headphone jack ribbon cable. /Guide/Installing-iPod-5th-Generation-Video-Battery/603/all#s3207 The front and back of the iPod should now be completely separated. /Guide/Installing-iPod-5th-Generation-Video-Battery/603/all#s3208 Be careful not to damage any of the headphone or battery ribbon cables while performing this step. Insert an iPod opening tool in between the metal case and battery at the location illustrated by the picture. Gently wiggle the tool while pushing it further in between the battery and back case. The adhesive holding the battery should give, allowing the battery to be removed from the rear panel. /Guide/Installing-iPod-5th-Generation-Video-Battery/603/all#s3209 Be careful not to damage any of the headphone or battery ribbon cables while performing this step. Insert an iPod opening tool in between the metal case and battery at the location illustrated by the picture. Gently wiggle the tool while pushing it further in between the battery and back case. The adhesive holding the battery should give, allowing the battery to be removed from the rear panel. /Guide/Installing-iPod-5th-Generation-Video-Battery/603/all#s3209 Be careful not to damage any of the headphone or battery ribbon cables while performing this step. Insert an iPod opening tool in between the metal case and battery at the location illustrated by the picture. Gently wiggle the tool while pushing it further in between the battery and back case. The adhesive holding the battery should give, allowing the battery to be removed from the rear panel. /Guide/Installing-iPod-5th-Generation-Video-Battery/603/all#s3209